- 您现在的位置：买卖IC网 > PDF目录378591 > DS2450S 1-Wire Quad A/D Converter PDF资料下载
参数资料
| 型号： | DS2450S |
| 英文描述： | 1-Wire Quad A/D Converter |
| 中文描述： | 1线四通道A / D转换器 |
| 文件页数： | 7/24页 |
| 文件大小： | 523K |
| 代理商： | DS2450S |
DS2450
7 of 24
102199
WRITE MEMORY [55H]
The Write Memory command is used to write to memory pages 1 and 2 in order to set the channel-
specific control data and alarm thresholds. The bus master will follow the command byte with a two byte
starting address (TA1=(T7:T0), TA2=(T15:T8)) and a data byte of (D7:D0). A 16-bit CRC of the
command byte, address bytes, and data byte is computed by the DS2450 and read back by the bus master
to confirm that the correct command word, starting address, and data byte were received. Now the
DS2450 copies the data byte to the specified memory location. With the next eight time slots the bus
master receives a copy of the same byte but read from memory for verification. If the verification fails, a
Reset Pulse should be issued and the current byte address should be written again.
If the bus master does not issue a Reset Pulse and the end of memory was not yet reached, the DS2450
will automatically increment its address counter to address the next memory location. The new two-byte
address will also be loaded into the 16-bit CRC-generator as a starting value. The bus master will send
the next byte using eight write time slots. As the DS2450 receives this byte it also shifts it into the CRC-
generator and the result is a 16-bit CRC of the new data byte and the new address. With the next sixteen
read time slots the bus master will read this 16-bit CRC from the DS2450 to verify that the address
incremented properly and the data byte was received correctly. If the CRC is incorrect, a Reset Pulse
should be issued in order to repeat the Write Memory command sequence.
Note that the initial pass through the Write Memory flow chart will generate a 16-bit CRC value that is
the result of shifting the command byte into the CRC-generator, followed by the two address bytes, and
finally the data byte. Subsequent passes through the Write Memory flow chart due to the DS2450
automatically incrementing its address counter will generate a 16-bit CRC that is the result of loading (not
shifting) the new (incremented) address into the CRC-generator and then shifting in the new data byte.
The decision to continue after having received a bad CRC or if the verification fails is made entirely by
the bus master. Write access to the conversion read-out registers is not possible. If a write attempt is
made to a page 0 address the device will follow the Write Memory flow chart correctly but the
verification of the data byte read back from memory will usually fail. The Write Memory command
sequence can be ended at any point by issuing a Reset Pulse.
相关PDF资料 |
PDF描述 |
|---|---|
| DS2480 | Serial 1.Wire Line Driver |
| DS2480S | Serial 1.Wire Line Driver |
| DS2490 | USB to 1-Wire Bridge Chip |
| DS2490S | USB to 1-Wire Bridge Chip |
| DS2502-E64 | IEEE EUI-64 Node Address Chip |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2450S/T&R | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| DS2450S+ | 功能描述:模数转换器 - ADC Quad 1-Wire RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| DS2450S+ | 制造商:Maxim Integrated Products 功能描述:SEMICONDUCTOR ((NW)) |
| DS2450S+T&R | 制造商:Maxim Integrated Products 功能描述:IC CONVERTER A/D QUAD 1-W 8-SOIC |
| DS2450S+T&R | 功能描述:模数转换器 - ADC Quad 1-Wire RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。