参数资料
型号: DS2505P
厂商: Maxim Integrated
文件页数: 15/24页
文件大小: 0K
描述: IC OTP 16KBIT 6TSOC
标准包装: 120
格式 - 存储器: EPROMs
存储器类型: EPROM OTP
存储容量: 16K(16K x 1)
接口: 1 线 串行
工作温度: -40°C ~ 85°C
封装/外壳: 6-LSOJ
供应商设备封装: 6-TSOC
包装: 管件

DS2505
Hardware Configuration
The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to
drive it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have an
open drain connection or 3-state outputs. The DS2505 is an open drain part with an internal circuit
equivalent to that shown in Figure 6. The bus master can be the same equivalent circuit. If a bi-
directional pin is not available, separate output and input pins can be tied together.
The bus master requires a pullup resistor at the master end of the bus, with the bus master circuit
equivalent to the one shown in Figures 7a and 7b. The value of the pullup resistor should be
approximately 5 k ? for short line lengths.
A multidrop bus consists of a 1-Wire bus with multiple slaves attached. The 1-Wire bus has a maximum
data rate of 16.3 kbits per second. If the bus master is also required to perform programming of the
EPROM portions of the DS2505, a programming supply capable of delivering up to 10 milliamps at
12 volts for 480 μs is required. The idle state for the 1-Wire bus is high. If, for any reason, a transaction
needs to be suspended, the bus MUST be left in the idle state if the transaction is to resume. If this does
not occur and the bus is left low for more than 120 μs, one or more of the devices on the bus may be
reset.
Transaction Sequence
The sequence for accessing the DS2505 via the 1-Wire port is as follows:
?
?
?
?
Initialization
ROM Function Command
Memory Function Command
Read/Write Memory/Status
INITIALIZATION
All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence
consists of a reset pulse transmitted by the bus master followed by a presence pulse(s) transmitted by the
slave(s).
The presence pulse lets the bus master know that the DS2505 is on the bus and is ready to operate. For
more details, see the “1-Wire Signaling” section.
ROM FUNCTION COMMANDS
Once the bus master has detected a presence, it can issue one of the four ROM function commands. All
ROM function commands are 8 bits long. A list of these commands follows (refer to flowchart in
Figure 8):
Read ROM [33H]
This command allows the bus master to read the DS2505’s 8-bit family code, unique 48–bit serial
number, and 8-bit CRC. This command can be used only if there is a single DS2505 on the bus. If more
than one slave is present on the bus, a data collision will occur when all slaves try to transmit at the same
time (open drain will produce a wired-AND result).
15 of 24
相关PDF资料
PDF描述
1-745496-8 CONN D-SUB PLUG 25P 22-26AWG AU
RGZ-0905D/HP CONV DC/DC 2W 09VIN +/-05VOUT
VE-JTZ-CX-B1 CONVERTER MOD DC/DC 2V 30W
GRM188R71C223KA01D CAP CER 0.022UF 16V 10% X7R 0603
DS2430A IC EEPROM 256BIT TO92-3
相关代理商/技术参数
参数描述
DS2505P/T&R 制造商:Maxim Integrated Products 功能描述:IC OTP 16KBIT 6TSOC
DS2505P/T&R 功能描述:可擦除可编程ROM RoHS:否 制造商:Maxim Integrated 类型: 存储容量:1024 bit 组织:1 K x 1 接口类型: 工作电流:5 uA 编程电压: 工作电源电压:2.8 V to 6 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:TO-92
DS2505P/TR 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:16Kb Add-Only Memory
DS2505P+ 功能描述:可擦除可编程ROM 16Kb Add-Only Memory RoHS:否 制造商:Maxim Integrated 类型: 存储容量:1024 bit 组织:1 K x 1 接口类型: 工作电流:5 uA 编程电压: 工作电源电压:2.8 V to 6 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:TO-92
DS2505P+T&R 制造商:Maxim Integrated Products 功能描述:EPROM OTP 16KBIT 64PAGES X 256 - Cut TR (SOS) 制造商:Maxim Integrated Products 功能描述:EPROM OTP 16KBIT 64PAGES X 256 6PIN TSOC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC OTP 16KBIT 6TSOC 制造商:Maxim Integrated Products 功能描述:EPROM 16Kb Add-Only Memory