- 您现在的位置：买卖IC网 > PDF目录19985 > DS2505P (Maxim Integrated)IC OTP 16KBIT 6TSOC PDF资料下载
参数资料
| 型号： | DS2505P |
| 厂商： | Maxim Integrated |
| 文件页数： | 22/24页 |
| 文件大小： | 0K |
| 描述： | IC OTP 16KBIT 6TSOC |
| 标准包装： | 120 |
| 格式 - 存储器： | EPROMs |
| 存储器类型： | EPROM OTP |
| 存储容量： | 16K（16K x 1） |
| 接口： | 1 线 串行 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 6-LSOJ |
| 供应商设备封装： | 6-TSOC |
| 包装： | 管件 |
DS2505
When reading the data memory of the DS2505 with the Extended Read Memory command, there are two
situations where a 16-bit CRC is transmitted. One 16-bit CRC follows each Redirection Byte; another
16-bit CRC is received after the last byte of a memory data page is read. The CRC at the end of the
memory page is always the result of clearing the CRC generator and shifting in the data bytes beginning
at the first addressed memory location of the EPROM data page until the last byte of this page. With the
initial pass through the Extended Read Memory flow chart the 16-bit CRC value is the result of shifting
the command byte into the cleared CRC generator, followed by the 2 address bytes and the Redirection
Byte. Subsequent passes through the Extended Read Memory flow chart will generate a 16-bit CRC that
is the result of clearing the CRC generator and then shifting in the Redirection Byte only.
When writing to the DS2505 (either data memory or status memory), the bus master receives a 16-bit
CRC to verify the correctness of the data transfer before applying the programming pulse. With the
initial pass through the Write Memory/Status flow chart the 16-bit CRC will be generated by clearing the
CRC-generator, shifting in the command, address low, address high and the data byte. Subsequent passes
through the Write Memory/Status flow chart due to the DS2505 automatically incrementing its address
counter will generate an 16-bit CRC that is the result of loading (not shifting) the new (incremented)
address into the CRC generator and then shifting in the new data byte.
The comparison of CRC values and decision to continue with an operation are determined entirely by the
bus master. There is no circuitry on the DS2505 that prevents a command sequence from proceeding if
the CRC stored in or calculated by the DS2505 does not match the value generated by the bus master.
For more details on generating CRC values including example implementations in both hardware and
software, see the Book of DS19xx iButton Standards.
CRC-16 HARDWARE DESCRIPTION AND POLYNOMIAL Figure 12
22 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| 1-745496-8 | CONN D-SUB PLUG 25P 22-26AWG AU |
| RGZ-0905D/HP | CONV DC/DC 2W 09VIN +/-05VOUT |
| VE-JTZ-CX-B1 | CONVERTER MOD DC/DC 2V 30W |
| GRM188R71C223KA01D | CAP CER 0.022UF 16V 10% X7R 0603 |
| DS2430A | IC EEPROM 256BIT TO92-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2505P/T&R | 制造商:Maxim Integrated Products 功能描述:IC OTP 16KBIT 6TSOC |
| DS2505P/T&R | 功能描述:可擦除可编程ROM RoHS:否 制造商:Maxim Integrated 类型: 存储容量:1024 bit 组织:1 K x 1 接口类型: 工作电流:5 uA 编程电压: 工作电源电压:2.8 V to 6 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:TO-92 |
| DS2505P/TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:16Kb Add-Only Memory |
| DS2505P+ | 功能描述:可擦除可编程ROM 16Kb Add-Only Memory RoHS:否 制造商:Maxim Integrated 类型: 存储容量:1024 bit 组织:1 K x 1 接口类型: 工作电流:5 uA 编程电压: 工作电源电压:2.8 V to 6 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:TO-92 |
| DS2505P+T&R | 制造商:Maxim Integrated Products 功能描述:EPROM OTP 16KBIT 64PAGES X 256 - Cut TR (SOS) 制造商:Maxim Integrated Products 功能描述:EPROM OTP 16KBIT 64PAGES X 256 6PIN TSOC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC OTP 16KBIT 6TSOC 制造商:Maxim Integrated Products 功能描述:EPROM 16Kb Add-Only Memory |
发布紧急采购，3分钟左右您将得到回复。