- 您现在的位置：买卖IC网 > PDF目录15877 > DS2703U+T&R (Maxim Integrated Products)IC BATT AUTHENTICATE SHA-1 8UMAX PDF资料下载
参数资料
| 型号： | DS2703U+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/20页 |
| 文件大小： | 0K |
| 描述： | IC BATT AUTHENTICATE SHA-1 8UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 3,000 |
| 功能： | 电池验证 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -20°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
DS2703 SHA-1 Battery Pack Authentication IC
TRANSACTION SEQUENCE
The protocol for accessing the DS2703 through the 1-Wire port is as follows:
Initialization
Net Address Command
Function Command(s)
Data Transfer (not all commands have data transfer)
All transactions of the 1-Wire bus begin with an initialization sequence consisting of a reset pulse transmitted by the
bus master, followed by a presence pulse simultaneously transmitted by the DS2703 and any other slaves on the
bus. The presence pulse tells the bus master that one or more devices are on the bus and ready to operate. For
more details, see the 1-Wire Signaling section below.
NET ADDRESS COMMANDS
Once the bus master has detected the presence of one or more slaves, it can issue one of the net address
commands described in the following paragraphs. The name of each Net Address command (ROM command) is
followed by the 8-bit opcode for that command in square brackets. Figure 6 presents a transaction flowchart of the
net address commands.
Read Net Address [33h]. This command allows the bus master to read the DS2703’s 1-Wire net address. This
command can only be used if there is a single slave on the bus. If more than one slave is present, a data collision
occurs when all slaves try to transmit at the same time (open drain produces a wired-AND result).
Match Net Address [55h]. This command allows the bus master to specifically address one DS2703 on the 1-Wire
bus. Only the addressed DS2703 responds to any subsequent function command. All other slave devices ignore
the function command and wait for a reset pulse. This command can be used with one or more slave devices on
the bus.
Skip Net Address [CCh]. This command saves time when there is only one DS2703 on the bus by allowing the
bus master to issue a function command without specifying the address of the slave. If more than one slave device
is present on the bus, a subsequent function command can cause a data collision when all slaves transmit data at
the same time.
Search Net Address [F0h]. This command allows the bus master to use a process of elimination to identify the
1-Wire net addresses of all slave devices on the bus. The search process involves the repetition of a simple three-
step routine: read a bit, read the complement of the bit, then write the desired value of that bit. The bus master
performs this simple three-step routine on each bit location of the net address. After one complete pass through all
64 bits, the bus master knows the address of one device. The remaining devices can then be identified on
additional iterations of the process. See Chapter 5 of the Book of DS19xx iButton ? Standards for a comprehensive
discussion of a net address search, including an actual example ( www.maxim-ic.com/iButtonBook ).
12 of 20
相关PDF资料 |
PDF描述 |
|---|---|
| UVR1A101MDD | CAP ALUM 100UF 10V 20% RADIAL |
| EBC35DRTF-S13 | CONN EDGECARD 70POS .100 EXTEND |
| RBC18DRYS | CONN EDGECARD 36POS DIP .100 SLD |
| ASC06DRYI-S13 | CONN EDGECARD 12POS .100 EXTEND |
| RCC20DRAN | CONN EDGECARD 40POS R/A .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2704 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:1280-Bit EEPROM with SHA-1 Authentication |
| DS2704-500-WAFER | 功能描述:电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| DS2704E+ | 制造商:Maxim Integrated Products 功能描述:1024 BIT MEM W/SHA-1 AUTH L/F - Rail/Tube |
| DS2704G+ | 功能描述:电可擦除可编程只读存储器 1280-Bit 电可擦除可编程只读存储器 w/SHA-1 Authent RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| DS2704G+T&R | 制造商:Maxim Integrated Products 功能描述:EEPROM SERL-1WIRE 1.25KBIT 5PAGES X 32 3.3V/5V 6TDFN EP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC EEPROM 1.25KBIT 6TDFN 制造商:Maxim Integrated Products 功能描述:EEPROM 1280-Bit EEPROM w/SHA-1 Authent |
发布紧急采购，3分钟左右您将得到回复。