- 您现在的位置：买卖IC网 > PDF目录15547 > DS2705U+T&R (Maxim Integrated Products)IC AUTHENTICATE SHA-1 8-UMAX PDF资料下载
参数资料
| 型号： | DS2705U+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/18页 |
| 文件大小： | 0K |
| 描述： | IC AUTHENTICATE SHA-1 8-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 3,000 |
| 功能： | 电池验证 |
| 电池化学： | 所有电池类型 |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
DS2705: SHA-1 Authentication Master
Write Data [6Ch, XX]. This command writes data starting at memory address XX. The LSb of the data to be stored
at address XX can be written immediately after the MSb of address has been entered. Because the address is
automatically incremented after the MSb of each byte is written, the LSb to be stored at address XX + 1 can be
written immediately after the MSb to be stored at address XX. If the bus master continues to write beyond address
FFh, the data starting at address 00 is overwritten. Writes to read-only addresses, reserved addresses and locked
EEPROM blocks are ignored. Incomplete bytes are not written. Write Data modifies the shadow RAM. A Copy Data
command is required to transfer data from the shadow to the EEPROM. See the Memory section for more details.
The Write command will cause spurious behavior if issued during an authentication attempt is in progress on the
MDQ pin.
Copy Data [48h]. This command copies the contents of all shadow RAM locations to EEPROM cells. After the
copy command is issued a high voltage pulse must be applied to the VPP pin for a time period of t PPW . See Figure 7
for example bus timing of an EEPROM program function. During the pulse, the bus master can issue read timeslots
on the bus. The DS2705 will respond with ‘0’s while the EEPROM copy is in progress, and ‘1’s after the copy is
complete. A reset on SDQ at any time during the copy sequence will prematurely terminate the operation.
Figure 7. Copy EEPROM Sequence
t PPR
VPP =
t PPW
14.5V MIN
t PPF
15.0V MAX
VPP = 0V
Non-critical Timing
1-Wire
Reset
SKIP ROM
Cmd
Copy Data
Cmd
Bus master may issue read slots during
EEPROM copy. DS2705 responds with
‘0’s during copy, ‘1’s afterwards.
Presence
Pulse
Recall Data [B8h]. This command recalls the contents of all EEPROM cell locations to the shadow RAM memory.
Following the Recall command, SDQ must be driven low for a minimum of t RSTL . SDQ can be driven low indefinitely
after the Recall command. The Recall command will cause spurious behavior if issued while an authentication
attempt is in progress on the MDQ pin.
15 of 18
相关PDF资料 |
PDF描述 |
|---|---|
| DS2762AE+T&R | IC MON BATT LI-ION HP 16-TSSOP |
| DS87001-E44 | ADAPTER MCU 44-TQFP TO 40-DIP |
| MAX6783TEB+ | IC BATT MON QUAD 5% 16TQFN |
| MAX6782TEC+ | IC BATT MON QUAD 10% 16TQFN |
| 1435834-9 | PATCHCORD CAT6 AMPTRAC WHITE 9' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2710EVKIT+ | 制造商:Maxim Integrated Products 功能描述:DS2710 EVAL KIT - Boxed Product (Development Kits) |
| DS2710G | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Cell NiMH Charger |
| DS2710G+ | 功能描述:电池管理 Single-Cell NiMH Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2710G+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:CHGR NIMH 10TDFN EP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC NIMH CHRGR SGL-CELL 10-TDFN |
| DS2710G+T&R | 功能描述:电池管理 Single-Cell NiMH Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。