参数资料
| 型号： | DS2712Z+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/15页 |
| 文件大小： | 0K |
| 描述： | IC NIMH CHARGER 16SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 镍金属氢化物 |
| 电源电压： | 4 V ~ 5.5 V |
| 工作温度： | -20°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
DS2711/DS2712: Loose-Cell NiMH Chargers
Parallel Charge Configuration
The parallel configuration supports two slot stand-alone chargers. Charge pulses are fed alternately to each cell
under the control of the CC1 and CC2 pins so the charge regimes occur in parallel. The duty cycle on CC1 and
CC2 are independent of one another. Transitions from precharge to fast charge, fast charge to top-off, and top-off
to maintenance occur independently for each cell.
The configuration shown in Figure 4 is for charging two cells with the current-sense feedback regulating the charge
source to 2A (RSNS = 0.068 ? ). The effective charge current for each cell is 2A x 0.484 = 0.968A. A charger with
battery holders designed to accept either AA or AAA cell sizes can be constructed with the current-sense
resistance split between two separate resistors so each cell type (AA or AAA) is charged at a different rate.
Mechanical design of the holders is required to prevent insertion of more than one cell in each slot. The holder
design must also prevent electrical contact with reverse polarity insertion.
Figure 4. Parallel Configuration with External Current Regulation
FCX718
ICHG
10K
FCX718
10K
100
100
DS2711/12
+5V
IFB
270
270
CC1
CC2
LED1
VSS
LED2
CSOUT
VP2
VP1
THM2
THM1
VDD
TMR
0.1
10K
x2
103AT-2
x2
VN1
VN0
CTST
DMSEL
75K
100K
RSNS
GND
0.068
The series or parallel charge configuration is programmed by strapping LED2 in the low, high, or high-Z state
during power-up. In this example and the following one, the parallel charge mode is selected by pulling LED2 pin
high during power-up. This is accomplished in this example by the LED and 270 ? resistor. In applications where
only one LED is used, a 100k ? pullup resistor is recommended. See Table 2 for additional configuration
programming information.
7 of 15
相关PDF资料 |
PDF描述 |
|---|---|
| DS2714E+ | IC NIMH CHARGER QUAD 20TSSOP |
| DS2715BZ+ | IC CTRLR CHRG NIMH BATT 16-SOIC |
| DS2726G+T&R | IC PROT LI+ 5-10CELL 32-TQFP |
| DS2731E+ | IC MANAGEMENT BACKUP 28-TSSOP |
| DS2741N+T | IC MONITOR/ACCUMULATOR 14-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2713MR00K | 制造商:Thomas & Betts 功能描述:200A,NLT,2P3W,MG,713,00K,125VDC |
| DS2714 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Quad Loose Cell NiMH Charger |
| DS2714E+ | 功能描述:电池管理 Quad Loose Cell NiMH Chargers RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2714E+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:QUAD LOOSECELL NIMHCHRGER TSSOP20LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC NIMH CHARGER QUAD 20TSSOP 制造商:Maxim Integrated Products 功能描述:Battery Management Quad Loose Cell NiMH Chargers |
| DS2714E+T&R | 功能描述:电池管理 Quad Loose Cell NiMH Chargers RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。