- 您现在的位置：买卖IC网 > PDF目录17125 > DS2761BE+025/T&R (Maxim Integrated Products)IC MON BATT LI-ION HP 16-TSSOP PDF资料下载
参数资料
| 型号： | DS2761BE+025/T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/24页 |
| 文件大小： | 0K |
| 描述： | IC MON BATT LI-ION HP 16-TSSOP |
| 标准包装： | 1,000 |
| 功能： | 电池监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
DS2761
a command sequence from proceeding as a result of a CRC mismatch. Proper use of the CRC can result
in a communication channel with a very high level of integrity.
The CRC can be generated by the host using a circuit consisting of a shift register and XOR gates as
shown in Figure 10, or it can be generated in software. Additional information about the Dallas 1-Wire
CRC is available in Application Note 27, Understanding and Using Cyclic Redundancy Checks with
Dallas Semiconductor Touch Memory Products . (This application not can be found on the Maxim/Dallas
Semiconductor website at www.maxim-ic.com).
In the circuit in Figure 14, the shift register bits are initialized to 0. Then, starting with the least
significant bit of the family code, one bit at a time is shifted in. After the 8th bit of the family code has
been entered, then the serial number is entered. After the 48th bit of the serial number has been entered,
the shift register contains the CRC value.
Figure 14. 1-WIRE CRC GENERATION BLOCK DIAGRAM
INPUT
MSb
XOR
XOR
LSb
XOR
HARDWARE CONFIGURATION
Because the 1-Wire bus has only a single line, it is important that each device on the bus be able to drive
it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must connect to the
bus with open-drain or tri-state output drivers. The DS2761 used an open-drain output driver as part of
the bidirectional interface circuitry shown in Figure 15. If a bidirectional pin is not available on the bus
master, separate output and input pins can be connected together.
The 1-Wire bus must have a pullup resistor at the bus-master end of the bus. For short line lengths, the
value of this resistor should be approximately 5k W . The idle state for the 1-Wire bus is high. If, for any
reason, a bus transaction must be suspended, the bus must be left in the idle state in order to properly
resume the transaction later. If the bus is left low for more than 120 m s, slave devices on the bus begin to
interpret the low period as a reset pulse, effectively terminating the transaction.
Figure 15. 1-WIRE BUS INTERFACE CIRCUITRY
BUS MASTER
Rx
Vpullup
(2.0V to 5.5V)
4.7k W
DS2761 1-WIRE PORT
Rx
Tx
Rx = RECEIVE
Tx = TRANSMIT
15 of 24
1 m A
(typ)
100 W
MOSFET
Tx
相关PDF资料 |
PDF描述 |
|---|---|
| AIRD-01-2R7M | INDUCTOR PWR DRUM CORE 2.7UH |
| VE-J5T-EZ | CONVERTER MOD DC/DC 6.5V 25W |
| DS2761BE+025 | IC MON BATT LI-ION HP 16-TSSOP |
| SPX431LAN-L/TR | IC VREF SHUNT PREC ADJ TO-92-3 |
| GCM15DCBI-S189 | CONN EDGECARD 30POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2761BX | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Precision Li+ Battery Monitor |
| DS2761BX-025 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Precision Li+ Battery Monitor |
| DS2761BX-025/T&R | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:IC MON BATT LI-ION HP FLIP-CHIP |
| DS2761BX-025/T&R | 功能描述:IC MON BATT LI-ION HP FLIP-CHIP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| DS2761K | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Li+ Battery Monitor Evaluation Kit |
发布紧急采购，3分钟左右您将得到回复。