- 您现在的位置：买卖IC网 > PDF目录16240 > DS2762AE+ (Maxim Integrated Products)IC MON BATT LI-ION HP 16-TSSOP PDF资料下载
参数资料
| 型号： | DS2762AE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/25页 |
| 文件大小： | 0K |
| 描述： | IC MON BATT LI-ION HP 16-TSSOP |
| 产品培训模块： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 功能： | 电池监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
DS2762 High-Precision Li+ Battery Monitor With Alerts
POWER MODES
The DS2762 has two power modes: active and sleep. While in active mode, the DS2762 continually measures
current, voltage, and temperature to provide data to the host system and to support current accumulation and Li+
safety monitoring. In sleep mode, the DS2762 ceases these activities. The DS2762 enters sleep mode when any of
the following conditions occurs:
§
§
§
The PMOD bit in the Status Register has been set to 1 and the DQ line is low for longer than 2s (pack
disconnection).
The voltage on V IN drops below undervoltage threshold V UV for t UVD (cell depletion).
The pack is disabled through the issuance of a SWAP command (SWEN bit = 1).
The DS2762 returns to active mode when any of the following occurs:
§
§
§
§
The PMOD bit has been set to 1 and the SWEN bit is set to 0 and the DQ line is pulled high (pack
connection).
The PS pin is pulled low (power switch).
The voltage on PLS becomes greater than the voltage on V IN (charger connection) with the SWEN bit set to 0.
The pack is enabled through the issuance of a SWAP command (SWEN bit = 1).
The DS2762 defaults to active mode when power is first applied.
Li+ PROTECTION CIRCUITRY
During active mode, the DS2762 constantly monitors cell voltage and current to protect the battery from overcharge
(overvoltage), overdischarge (undervoltage), and excessive charge and discharge currents (overcurrent, short
circuit). Conditions and DS2762 responses are described in the following sections and summarized in Table 1 and
Figure 3.
Table 1. Li+ Protection Conditions and DS2762 Responses
V PLS > V DD
CONDITION
Overvoltage
Undervoltage
THRESHOLD
V IN > V OV
V IN < V UV
ACTIVATION
DELAY
t OVD
t UVD
RESPONSE
CC high
CC, DC high,
Sleep Mode
RELEASE THRESHOLD
V IN < V CE , or
V IS ≤ -2mV
(1)
(charger connected)
V IS > V OC
V IS < -V OC
Overcurrent, Charge
Overcurrent, Discharge
Short Circuit
(2)
(2)
V SNS > V SC
t OCD
t OCD
t SCD
CC, DC high
DC high
DC high
V PLS < V DD - V TP
V PLS > V DD - V TP
V PLS > V DD - V TP
(3)
(4)
(4)
V IS = V IS1 - V IS2 . Logic high = V PLS for CC and V DD for DC . All voltages are with respect to V SS . I SNS references current delivered from pin SNS.
Note 1:
Note 2:
Note 3:
Note 4:
If V DD < 2.2V, release is delayed until the recovery charge current (I RC ) passed from PLS to V DD charges the battery and allows V DD
to exceed 2.2V.
For the internal sense resistor configuration, the overcurrent thresholds are expressed in terms of current: I SNS > I OC for charge
direction and I SNS < -I OC for discharge direction.
With test current I TST flowing from PLS to V SS (pulldown on PLS).
With test current I TST flowing from V DD to PLS (pullup on PLS).
Overvoltage. If the cell voltage on V IN exceeds the overvoltage threshold, V OV , for a period longer than overvoltage
delay, t OVD , the DS2762 shuts off the external charge FET and sets the OV flag in the protection register. When the
cell voltage falls below charge enable threshold V CE , the DS2762 turns the charge FET back on (unless another
protection condition prevents it). Discharging remains enabled during overvoltage, and the DS2762 re-enables the
charge FET before V IN < V CE if a discharge current of -80mA (V IS ≤ -2mV) or less is detected.
Undervoltage. If the voltage of the cell drops below undervoltage threshold, V UV , for a period longer than
undervoltage delay, t UVD , the DS2762 shuts off the charge and discharge FETs, sets the UV flag in the protection
9 of 25
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J7H-EZ-F3 | CONVERTER MOD DC/DC 52V 25W |
| RP08-4805SA | CONV DC/DC 8W 36-75VIN 05VOUT |
| VE-J7H-EZ-F2 | CONVERTER MOD DC/DC 52V 25W |
| RP08-243.3SA | CONV DC/DC 8W 18-36VIN 3.3VOUT |
| MAX1737EEI+ | IC BATT CHRG CTRLR 4-LI+ 28-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2762AE/T&R | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2762AE/TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:High-Precision Li+ Battery Monitor With Alerts |
| DS2762AE+ | 功能描述:电池管理 High-Prec Li+ Bat Monitor w/Alerts RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2762AE+025 | 功能描述:电池管理 High-Prec Li+ Bat Monitor w/Alerts RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2762AE+025/T&R | 制造商:Maxim Integrated Products 功能描述:MONITOR LI-ION 4.275V 16TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MON BATT LI-ION HP 16-TSSOP 制造商:Maxim Integrated Products 功能描述:Battery Management High-Prec Li+ Bat Monitor w/Alerts |
发布紧急采购，3分钟左右您将得到回复。