- 您现在的位置：买卖IC网 > PDF目录16239 > DS2780G+ (Maxim Integrated Products)IC FUEL GAUGE STAND ALONE 10TDFN PDF资料下载
参数资料
| 型号： | DS2780G+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/31页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE STAND ALONE 10TDFN |
| 产品培训模块： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-TDFN-EP（3x4） |
| 包装： | 管件 |
| 产品目录页面： | 1436 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
DS2780 Standalone Fuel Gauge IC
Figure 17. EEPROM REGISTER FORMAT
Address
1Fh
Bit Definition
Field
EEC
Bit
7
Format
Read Only
Allowable Values
EEPROM Copy Flag
Set to 1 when: Copy Data command executed
Cleared to 0 when: Copy Data command completes
Note: While EEC = 1, writes to EEPROM addresses are ignored
Power-up default: 0
LOCK
6
Read /
Write to 1
EEPROM Lock Enable
Host write to 1: Enables the Lock command. Host must issue Lock
command as next command after writing Lock Enable bit to 1.
Cleared to 0 when: Lock command completes or when the Lock
command is not issued immediately following the setting of the Lock
Enable bit.
Power-up default: 0
Reserved
2:6
Undefined
BL1
1
Read Only
EEPROM Block 1 Lock Flag (Parameter EEPROM 60h – 7Fh)
0: EEPROM is not locked
1: EEPROM block is locked
Factory default: 0
BL0
0
Read Only
EEPROM Block 0 Lock Flag (User EEPROM 20h – 2Fh)
0: EEPROM is not locked
1: EEPROM block is locked
Factory default: 0
MEMORY
The DS2780 has a 256 byte linear memory space with registers for instrumentation, status, and control, as well as
EEPROM memory blocks to store parameters and user information. Byte addresses designated as “Reserved”
return undefined data when read. Reserved bytes should not be written. Several byte registers are paired into two-
byte registers in order to store 16-bit values. The most significant byte (MSB) of the 16 bit value is located at a
even address and the least significant byte (LSB) is located at the next address (odd) byte. When the MSB of a
two-byte register is read, the MSB and LSB are latched simultaneously and held for the duration of the read data
command to prevent updates to the LSB during the read. This ensures synchronization between the two register
bytes. For consistent results, always read the MSB and the LSB of a two-byte register during the same read data
command sequence.
EEPROM memory consists of the non-volatile EEPROM cells overlaid with volatile shadow RAM. The Read Data
and Write Data commands allow the 1-Wire interface to directly access the shadow RAM only. The Copy Data and
Recall Data function commands transfer data between the shadow RAM and the EEPROM cells. In order to modify
the data stored in the EEPROM cells, data must be written to the shadow RAM and then copied to the EEPROM.
In order to verify the data stored in the EEPROM cells, the EEPROM data must be recalled to the shadow RAM
and then read from the shadow RAM.
USER EEPROM
A 16 byte User EEPROM memory (block 0, addresses 20h - 2Fh) provides non-volatile memory that is
uncommitted to other DS2780 functions. Accessing the User EEPROM block does not affect the operation of the
DS2780. User EEPROM is lockable, and once locked, write access is not allowed. The battery pack or host system
manufacturer can program lot codes, date codes and other manufacturing, warranty, or diagnostic information and
then lock it to safeguard the data. User EEPROM can also store parameters for charging to support different size
batteries in a host device as well as auxiliary model data such as time to full charge estimation parameters.
PARAMETER EEPROM
Model data for the cells, as well as application operating parameters are stored in the Parameter EEPROM (block
1, addresses 60h - 7Fh). The ACR (MSB and LSB) and AS registers are automatically saved to EEPROM when
20 of 31
相关PDF资料 |
PDF描述 |
|---|---|
| RMM11DRUI | CONN EDGECARD 22POS DIP .156 SLD |
| M3BGK-1620K | IDC CABLE - MSR16K/MC16F/MCS16K |
| RBM24DCWS | CONN EDGECARD 48POS DIP .156 SLD |
| RP08-483.3SA | CONV DC/DC 8W 36-75VIN 3.3VOUT |
| M3BEK-1620K | IDC CABLE - MSR16K/MC16F/MCE16K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2780G+ | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2780G+T&R | 制造商:Maxim Integrated Products 功能描述:STANDALONE FUELGAUGE 10-TDFN T&R LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE STAND ALONE 10TDFN 制造商:Maxim Integrated Products 功能描述:Battery Management Stand-Alone Fuel Gauge |
| DS2780G+T&R | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2780G+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Standalone Fuel Gauge IC |
| DS2780K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。