- 您现在的位置：买卖IC网 > PDF目录16239 > DS2780G+ (Maxim Integrated Products)IC FUEL GAUGE STAND ALONE 10TDFN PDF资料下载
参数资料
| 型号： | DS2780G+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/31页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE STAND ALONE 10TDFN |
| 产品培训模块： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-TDFN-EP（3x4） |
| 包装： | 管件 |
| 产品目录页面： | 1436 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
DS2780 Standalone Fuel Gauge IC
fuel gauge data to EEPROM, but some data loss can occur depending on the timing of the protection event and the
backup. When the protection circuit is connected directly to the battery the protection is absolute, no charging will
occur during a protection event. With the protection circuit located outside, see Figure 3, the DS2780 will remain
powered up during a protection event. The disadvantage to this configuration is that you run the risk of
overcharging the battery by creating an unintentional charge path from PK+ to DATA or PIO (V PK+ > V CELL + V DIODE ).
Communication to the DS2780 is broken during a protection event regardless of protector location.
POWER MODES
The DS2780 has two power modes: ACTIVE and SLEEP. On initial power up, the DS2780 defaults to ACTIVE
mode. While in ACTIVE mode, the DS2780 is fully functional with measurements and capacity estimation
continuously updated. In SLEEP mode, the DS2780 conserves power by disabling measurement and capacity
estimation functions, but preserves register contents. SLEEP mode is entered under two different conditions and
an enable bit for each condition makes entry into SLEEP optional. SLEEP mode can be enabled using the Power
Mode (PMOD) bit or the Under Voltage Enable (UVEN) bit.
The PMOD type SLEEP is entered if the PMOD bit is set AND DQ is low for t SLEEP (2s nominal). The condition of
DQ low for t SLEEP can be used to detect a pack disconnection or system shutdown, in which no charge or discharge
current will flow. A PMOD SLEEP condition transitions back to ACTIVE mode when DQ is pulled high.
The second option for entering SLEEP is an under voltage condition. When the UVEN bit is set, the DS2780
transitions to SLEEP if the voltage on VIN is less than V SLEEP (2.45V nominal) AND DQ is stable at a low or high
logic level for t SLEEP . An under-voltage condition occurs when a pack is fully discharged, where loading on the
battery should be minimized. UVEN type SLEEP relieves the battery of the I ACTIVE load until communication on DQ
resumes.
NOTE: PMOD and UVEN SLEEP features must be disabled when a battery is charged on an external charger that
does not connect to the DQ pin. PMOD SLEEP can be used if the charger pulls DQ high. UVEN SLEEP can be
used if the charger toggles DQ. The DS2780 remains in SLEEP on a charger that fails to properly drive DQ and
therefore does not measure or accumulate current when a battery is charged.
INITIATING COMMUNICATION IN SLEEP
When beginning communication with a DS2780 in PMOD SLEEP, DQ must be pulled up first and then a 1-Wire
Reset pulse must be issued by the master. In UVEN SLEEP, the procedure depends on the state of DQ when
UVEN SLEEP was entered. If DQ was low, DQ must be pulled up and then a 1-Wire Reset pulse must be issued
by the master as with PMOD SLEEP. If DQ was high when UVEN SLEEP was entered, then the DS2780 is
prepared to receive a 1-Wire reset from the master. In the first two cases with DQ low during SLEEP, the DS2780
does not respond to the first rising edge of DQ with a presence pulse.
VOLTAGE MEASUREMENT
Battery voltage is measured at the VIN input with respect to VSS. It has a range of 0V to 4.992V (pin voltage
limited to 4.5V) and a resolution of 4.88mV. The measurement is stored in the VOLTAGE register in two’s
compliment form and is updated every 440ms. Voltages above the maximum register value are reported at the
maximum value; voltages below the minimum register value are reported at the minimum value. The format of the
voltage register is shown in Figure 4.
Figure 4. Voltage Register Format
VOLT
MSB—Address 0Ch
LSB—Address 0Dh
Read Only
S
2 9
2 8
2 7
2 6
2 5
2 4
2 3
2 2
2 1
2 0
X
X
X
X
X
MSb
“S”: sign bit(s), “X”: reserved
LSb
MSb
LSb
Units: 4.88mV
7 of 31
相关PDF资料 |
PDF描述 |
|---|---|
| RMM11DRUI | CONN EDGECARD 22POS DIP .156 SLD |
| M3BGK-1620K | IDC CABLE - MSR16K/MC16F/MCS16K |
| RBM24DCWS | CONN EDGECARD 48POS DIP .156 SLD |
| RP08-483.3SA | CONV DC/DC 8W 36-75VIN 3.3VOUT |
| M3BEK-1620K | IDC CABLE - MSR16K/MC16F/MCE16K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2780G+ | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2780G+T&R | 制造商:Maxim Integrated Products 功能描述:STANDALONE FUELGAUGE 10-TDFN T&R LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE STAND ALONE 10TDFN 制造商:Maxim Integrated Products 功能描述:Battery Management Stand-Alone Fuel Gauge |
| DS2780G+T&R | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2780G+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Standalone Fuel Gauge IC |
| DS2780K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。