- 您现在的位置：买卖IC网 > PDF目录1788 > DS2786G-5+T&R (Maxim Integrated Products)IC FUEL GAUGE OCV-BASED 10-TDFN PDF资料下载
参数资料
| 型号： | DS2786G-5+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/22页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE OCV-BASED 10-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-TDFN-EP（3x4） |
| 包装： | 带卷 (TR) |
DS2786 Stand-Alone OCV-Based Fuel Gauge
COMMAND REGISTER
The Command Register is read/write accessible. Bit values indicate operations requested to be performed by the
device.
Figure 23. Command Register Format
ADDRESS Feh
BIT 7
POR
BIT 6
0
BIT 5
X
BIT 4
X
BIT 3
POCV
BIT 2
SOCV
BIT 1
RCALL
BIT 0
COPY
Bit 7: POR —Power-On Reset. A value of 1 starts a power-on reset event. The bit is cleared on the next start or
stop on the 2-Wire bus, exiting the reset state.
Bit 6: 0 —Bit always reads logic 0.
Bits 5 and 4: X —Reserved.
Bit 3: POCV —Present OCV Calculation. When set to one the part is performing an OCV calculation based on the
voltage stored in the Voltage Register, and the OCV lookup table values present in the scratch pad. Writing the bit
to 1 forces a calculation. This function should be used for test purposes only. Forcing an OCV calculation will
create capacity estimation error. The bit is cleared when the hardware completes the calculation.
Bit 2: SOCV —Stored OCV Calculation. This command may be used to reset the Relative Capacity calculation after
updating OCV cell model data in the Scratchpad. When set to one the part is performing an OCV calculation based
on the voltage stored in the Initial Voltage Register, and the OCV lookup table values present in the scratch pad.
Writing the bit to 1 forces a calculation. Forcing an OCV calculation will create capacity estimation error. The bit is
cleared when the hardware completes the calculation.
Bit 1: RCALL —The Recall bit is set to recall the contents of EEPROM into the scratch pad.
Bit 0: COPY —The Copy bit is set to start a copy command of the scratch pad to EEPROM. A programming voltage
must be present on the VPROG pin prior for the copy to be successful. The COPY bit must be cleared by software
within the t PROG time window.
USER EEPROM
Location 7Fh provides one byte available for storage of user-defined information. This byte does not affect
operation of the fuel gauge. Factory default is 00h.
2-WIRE BUS SYSTEM
The 2-Wire bus system supports operation as a slave only device in a single or multislave, and single- or
multimaster system. The 2-wire interface consists of a serial data line (SDA) and serial clock line (SCL). SDA and
SCL provide bidirectional communication between the DS2786 slave device and a master device at speeds up to
400kHz. The DS2786’s SDA pin operates bidirectionally, that is, when the DS2786 receives data, SDA operates as
an input, and when the DS2786 returns data, SDA operates as an open-drain output, with the host system
providing a resistive pullup. The DS2786 always operates as a slave device, receiving and transmitting data under
the control of a master device. The master initiates all transactions on the bus and generates the SCL signal as
well as the START and STOP bits which begin and end each transaction.
Bit Transfer
One data bit is transferred during each SCL clock cycle, with the cycle defined by SCL transitioning low-to-high and
then high-to-low. The SDA logic level must remain stable during the high period of the SCL clock pulse. Any
change in SDA when SCL is high is interpreted as a START or STOP control signal.
18 of 22
相关PDF资料 |
PDF描述 |
|---|---|
| DS2788E+T&R | IC FUEL GAUGE W/DSP DRV 14TSSOP |
| DS2790G+T&R | IC FUEL GAUGE BATT 28-TDFN |
| DS3881E+T&R | IC CCFL CONTROL 24TSSOP |
| DS3882E+T&R | IC CCFL CNTRLR DUAL 28TSSOP |
| DS3984T+ | IC CCFL CNTRLR 4CH 32-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2786K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS2786K-SMP | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS2788 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel-Gauge IC with LED Display Drivers |
| DS2788_09 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel-Gauge IC with LED Display Drivers |
| DS2788E+ | 功能描述:电池管理 Stand-Alone F-Gauge w/LED Display Drvrs RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。