参数资料
| 型号： | DS28EC20P+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 21/27页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 20KBIT 6TSOC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 4,000 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 20K（256 x 80） |
| 接口： | 1 线 串行 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 6-LSOJ |
| 供应商设备封装： | 6-TSOC |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页
DS28EC20: 20Kb 1-Wire EEPROM
1-Wire SIGNALING
The DS28EC20 requires strict protocols to ensure data integrity. The protocol consists of four types of signaling on
one line: reset sequence with reset pulse and presence pulse, write-zero, write-one, and read-data. Except for the
presence pulse, the bus master initiates all falling edges. The DS28EC20 can communicate at two different
speeds: standard speed and overdrive speed. If not explicitly set into the Overdrive mode, the DS28EC20
communicates at standard speed. While in Overdrive mode the fast timing applies to all waveforms. For operation
at overdrive speed, the DS28EC20 requires V PUP to be 5V ±5%.
To get from idle to active, the voltage on the 1-Wire line needs to fall from V PUP below the threshold V TL . To get
from active to idle, the voltage needs to rise from V ILMAX past the threshold V TH . The time it takes for the voltage to
make this rise is seen in Figure 10 as ε , and its duration depends on the pullup resistor (R PUP ) used and the
capacitance of the 1-Wire network attached. The voltage V ILMAX is relevant for the DS28EC20 when determining a
logical level, not triggering any events.
Figure 10 shows the initialization sequence required to begin any communication with the DS28EC20. A reset
pulse followed by a presence pulse indicates that the DS28EC20 is ready to receive data, given the correct ROM
and memory function command. If the bus master uses slew-rate control on the falling edge, it must pull down the
line for t RSTL + t F to compensate for the edge. A t RSTL duration of 480μs or longer exits the Overdrive mode,
returning the device to standard speed. If the DS28EC20 is in Overdrive mode and t RSTL is no longer than 80μs, the
device remains in Overdrive mode. If the device is in Overdrive mode and t RSTL is between 80μs and 480μs, the
device resets, but the communication speed is undetermined.
Figure 10. Initialization Procedure: Reset and Presence Pulse
After the bus master has released the line it goes into Receive mode. Now the 1-Wire bus is pulled to V PUP through
the pullup resistor, or in case of a DS2482-x00 or DS2480B driver, by active circuitry. When the threshold V TH is
crossed, the DS28EC20 waits for t PDH and then transmits a presence pulse by pulling the line low for t PDL . To detect
a presence pulse, the master must test the logical state of the 1-Wire line at t MSP .
The t RSTH window must be at least the sum of t PDHMAX , t PDLMAX , and t RECMIN . Immediately after t RSTH is expired, the
DS28EC20 is ready for data communication. In a mixed population network, t RSTH should be extended to minimum
480μs at standard speed and 48μs at overdrive speed to accommodate other 1-Wire devices.
Read-/Write-Time Slots
Data communication with the DS28EC20 takes place in time slots, which carry a single bit each. Write-time slots
transport data from bus master to slave. Read-time slots transfer data from slave to master. Figure 11 illustrates
the definitions of the write- and read-time slots.
All communication begins with the master pulling the data line low. As the voltage on the 1-Wire line falls below the
threshold V TL , the DS28EC20 starts its internal timing generator that determines when the data line is sampled
during a write-time slot and how long data is valid during a read-time slot.
21 of 27
相关PDF资料 |
PDF描述 |
|---|---|
| FA5S040HP1R3000 | CONN FFC/FPC 0.5MM 40POS R/A SMD |
| XF2M-1215-1A-R100 | CONNECTOR FPC 12POS 0.5MM SMD |
| FT24C512A-UTG-B | IC EEPROM 512KBIT 1MHZ 8TSSOP |
| FT24C512A-UTR-B | IC EEPROM 512KBIT 1MHZ 8TSSOP |
| FT24C512A-USG-B | IC EEPROM 512KBIT 1MHZ 8SOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS28EC20Q-A5A-5A+T | 制造商:Maxim Integrated Products 功能描述:20KB 1-WIRE EEPROM - Tape and Reel |
| DS28EC20Q-A5A-5A+W | 制造商:Maxim Integrated Products 功能描述:20KB 1-WIRE EEPROM - Rail/Tube |
| DS28EL15 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:DeepCover Secure Authenticator with 1-Wire SHA-256 and 512-Bit User EEPROM |
| DS28EL15Q+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:DeepCover Secure Authenticator with 1-Wire SHA-256 and 512-Bit User EEPROM |
| DS28EL25 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:DeepCover Secure Authenticator with 1-Wire SHA-256 with 4Kb User EEPROM |
发布紧急采购，3分钟左右您将得到回复。