- 您现在的位置：买卖IC网 > PDF目录17033 > DS5000T/KIT (Maxim Integrated Products)KIT IC EVALUATION MPU/RTC PDF资料下载
参数资料
| 型号： | DS5000T/KIT |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/19页 |
| 文件大小： | 0K |
| 描述： | KIT IC EVALUATION MPU/RTC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 微控制器 |
| 适用于相关产品： | DS5000 |
| 所含物品： | 演示板和软件 |
DS5000(T)
6 of 19
PROGRAM LOADING CONFIGURATIONS Figure 3
Table 1 summarizes the selection of the available Parallel Program Load cycles. The timing associated
with these cycles is illustrated in the electrical specs.
SERIAL BOOTSTRAP LOADER
The Serial Program Load Mode is the easiest, fastest, most reliable, and most complete method of
initially loading application software into the DS5000(T) nonvolatile RAM. Communication can be
performed over a standard asynchronous serial communications port. A typical application would use a
simple RS232C serial interface to program the DS5000(T) as a final production procedure. The hardware
configuration required for the Serial Program Load mode is illustrated in Figure 3. Port pins 2.7 and 2.6
must be either open or pulled high to avoid placing the DS5000(T) in a parallel load cycle. Although an
11.0592 MHz crystal is shown in Figure 3, a variety of crystal frequencies and loader baud rates are
supported, shown in Table 2. The serial loader is designed to operate across a 3-wire interface from a
standard UART. The receive, transmit, and ground wires are all that are necessary to establish
communication with the DS5000(T).
The Serial Bootstrap Loader implements an easy-to-use command line interface that allows an application
program in an Intel hex representation to be loaded into and read back from the device. Intel hex is the
typical format which existing 8051 cross-assemblers output. The serial loader responds to single
character commands, which are summarized below:
相关PDF资料 |
PDF描述 |
|---|---|
| AFS-EVAL-KIT | KIT STARTER EVAL FUSION AFS600 |
| ESM10DRYS | CONN EDGECARD 20POS DIP .156 SLD |
| EMM11DRTN | CONN EDGECARD 22POS DIP .156 SLD |
| AGL-ICICLE-KIT | KIT EVAL FOR IGOO ICICLE |
| ECM25DCCN | CONN EDGECARD 50POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS5001FP | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:128k Soft Microprocessor Chip |
| DS5001FP_05 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:128k Soft Microprocessor Chip |
| DS5001FP08 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| DS5001FP-12 | 功能描述:微处理器 - MPU RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| DS5001FP-12-44 | 制造商:Maxim Integrated Products 功能描述:MCU 8BIT CISC ROMLESS 5V 80MQFP - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。