参数资料
型号: DS75S
厂商: DALLAS SEMICONDUCTOR
元件分类: Switch/Digital Output Temperature Sensor
英文描述: DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT
封装: 0.150 INCH, SOIC-8
文件页数: 8/13页
文件大小: 240K
代理商: DS75S
DS75
4 of 13
Temperature/Data Relationships Table 2
S2
6
2
5
2
4
2
3
2
1
2
0
MSB
MSb
(UNIT =
°C)
LSb
2
–1
2
–2
2
–3
2
–4
00
LSB
TEMPERATURE/DATA RELATIONSHIPS
Table 2 cont’d
TEMP
DIGITAL OUTPUT
(Binary)
DIGITAL
OUTPUT
(Hex)
+125
°C
0111 1101 0000 0000
7D00h
+25.0625
°C
0001 1001 0001 0000
1910h
+10.125
°C
0000 1010 0010 0000
0A20h
+0.5
°C
0000 0000 1000 0000
0080h
+0
°C
0000 0000 0000 0000
0000h
–0.5
°C
1111 1111 1000 0000
FF80h
–10.125
°C
1111 0101 1110 0000
E5E0h
–25.0625
°C
1110 0110 1111 0000
E6F0h
–55
°C
1100 1001 0000 0000
C900h
OPERATION–Thermostat Control
In its comparator operating mode, the DS75 functions as a thermostat with programmable hysteresis, as
shown in Figure 2. When the DS75’s temperature meets or exceeds the value stored in the high tempera-
ture trip register (TOS ) a consecutive number of times defined by the configuration register, the output
becomes active, and will stay active until the temperature falls below the temperature stored in the low
temperature trigger register (THYST ) the first time. In this way, any amount of hysteresis may be obtained.
The DS75 powers up in the comparator mode with TOS =80
°C and T
HYST =75
°C, and the device can be
used as a standalone thermostat (no 2–wire interface required) with those setpoints.
In the interrupt mode, the O.S. output will first become active following the programmed number of
consecutive conversions above TOS . The fault can only be cleared by either setting the DS75 in a
shutdown mode or by reading any register (temperature, configuration, TOS, or THYST ) on the device.
Following a clear, a subsequent fault can only occur if consecutive conversions fall below THYST. This
interrupt/clear process is thus cyclical (TOS, clear, THYST, clear, TOS, clear, THYST, clear, . . .). Only the
first of multiple consecutive TOS violations will activate O.S., even if each fault is separated by a clearing
function. The same situation applies to multiple consecutive THYST events.
相关PDF资料
PDF描述
DS75U/T&R DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT
DS75U-C12+T&R DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT
DS75U DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT
DS75S DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT
DS80C310-QCG 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44
相关代理商/技术参数
参数描述
DS75S/T&R 制造商:Maxim Integrated Products 功能描述:2-WIRE THERMAL WATCHDOG SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC WATCHDOG THERM 2-W 3/5V 8SOIC
DS75S/T&R 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS75S+ 功能描述:板上安装温度传感器 Digital RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS75S+/ 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS75S+T&R 制造商:Maxim Integrated Products 功能描述:DS75 LEAD FREE SO 8 T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Digital 制造商:Maxim Integrated Products 功能描述:Temp Sensor Digital Serial (2-Wire) SO8