- 您现在的位置：买卖IC网 > PDF目录97869 > DS75S (DALLAS SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | DS75S |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封装： | 0.150 INCH, SOIC-8 |
| 文件页数： | 9/13页 |
| 文件大小： | 240K |
| 代理商： | DS75S |
DS75
5 of 13
O.S. OUTPUT TRANSFER FUNCTION Figure 2
Regardless of the mode chosen, the O.S. output is open–drain and the active state is set in the configura-
tion register. The power–up default is active low. Refer to the “OPERATION–Programming” section for
instructions in adjusting the thermostat setpoints, thermostat mode, and O.S. active state.
OPERATION–Programming
There are three areas of interest in programming the DS75: Configuration register, TOS register, and the
THYST register. All programming is done via the 2–wire interface by setting the pointer to the appropriate
location. Table 3 illustrates the pointer settings for the four registers of the DS75.
Pointer Register Structure Table 3
POINTER
ACTIVE REGISTER
00h
Temperature (default)
01h
Configuration
02h
THYST
03h
TOS
The DS75 will power up with the temperature register selected. If the host wishes to change the data
pointer, it simply addresses the DS75 in the write mode (R/W=0), receives an acknowledge, and writes
the 8 bits that correspond to the new desired location. The last pointer location is always maintained so
that consecutive reads from the same register do not require the host to always provide a pointer address.
The only exception is at power–up, in which case the pointer will always be set to 00h, the temperature
register. The pointer address must always proceed data in writing to a register, regardless of which
address is currently selected. Please refer to the “2–Wire Serial Data Bus” section for details of the 2–
wire bus protocol.
相关PDF资料 |
PDF描述 |
|---|---|
| DS75U/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
| DS75U-C12+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
| DS75U | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
| DS75S | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS80C310-QCG | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS75S/T&R | 制造商:Maxim Integrated Products 功能描述:2-WIRE THERMAL WATCHDOG SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC WATCHDOG THERM 2-W 3/5V 8SOIC |
| DS75S/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS75S+ | 功能描述:板上安装温度传感器 Digital RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS75S+/ | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS75S+T&R | 制造商:Maxim Integrated Products 功能描述:DS75 LEAD FREE SO 8 T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Digital 制造商:Maxim Integrated Products 功能描述:Temp Sensor Digital Serial (2-Wire) SO8 |
发布紧急采购，3分钟左右您将得到回复。