- 您现在的位置：买卖IC网 > PDF目录11742 > DS8113-JNG+T&R (Maxim Integrated Products)IC INTERFACE SMART CARD 28-TSSOP PDF资料下载
参数资料
| 型号： | DS8113-JNG+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/17页 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE SMART CARD 28-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 智能卡 |
| 接口： | 模拟 |
| 电源电压： | 2.7 V ~ 6 V |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
DS8113
Deactivation Sequence
When a session is completed, the host microcontroller
sets the CMDVCC line high to execute an automatic
deactivation sequence and returns the card interface to
the inactive mode (Figure 5).
1) RST goes low (t10).
2) CLK is held low (t12 = t10 + 0.5
× T) where T is 64
times the period of the internal oscillator (approxi-
mately 25s).
3) I/O, AUX1, and AUX2 are pulled low (t13 = t10 + T).
4) VCC starts to fall (t14 = t10 + 1.5
× T).
5) When VCC reaches its inactive state, the deactiva-
tion sequence is complete (at tDE).
6) All card contacts become low impedance to GND;
I/OIN, AUX1IN, and AUX2IN remain at VDD (pulled
up through an 11k
Ω resistor).
7) The internal oscillator returns to its lower frequency.
VCC Generator
The VCC generator has a capacity to supply up to
80mA continuously at 5V, 65mA at 3V, and 30mA at
1.8V. An internal overload detector triggers at approxi-
mately 120mA. Current samples to the detector are fil-
tered. This allows spurious current pulses (with a
duration of a few s) up to 200mA to be drawn without
causing deactivation. The average current must stay
below the specified maximum current value. To main-
tain VCC voltage accuracy, a 100nF capacitor (with an
ESR < 100m
Ω) should be connected to CGND and
placed near the DS8113’s VCC pin, and a 100nF or
220nF capacitor (220nF is the best choice) with the
same ESR should be connected to CGND and placed
near the smart card reader’s C1 contact.
Fault Detection
The following fault conditions are monitored:
Short-circuit or high current on VCC
Removal of a card during a transaction
VDD dropping
Card voltage generator operating out of the speci-
fied values (VDDA too low or current consumption
too high)
Overheating
There are two different cases (Figure 6):
CMDVCC High Outside a Card Session. Output
OFF is low if a card is not in the card reader and
high if a card is in the reader. The VDD supply is
monitored—a decrease in input voltage generates
an internal power-on reset pulse but does not
affect the OFF signal. Short-circuit and tempera-
ture detection is disabled because the card is not
powered up.
CMDVCC Low Within a Card Session. Output
OFF goes low when a fault condition is detected,
and an emergency deactivation is performed auto-
matically (Figure 7). When the system controller
resets CMDVCC to high, it may sense the OFF
level again after completing the deactivation
sequence. This distinguishes between a card
extraction and a hardware problem (OFF goes high
again if a card is present). Depending on the con-
nector’s card-present switch (normally closed or
normally open) and the mechanical characteristics
of the switch, bouncing can occur on the PRES sig-
nals at card insertion or withdrawal.
The DS8113 has a debounce feature with an 8ms typi-
cal duration (Figure 6). When a card is inserted, output
OFF goes high after the debounce time delay. When
the card is extracted, an automatic deactivation
sequence of the card is performed on the first true/false
transition on PRES and output OFF goes low.
Smart Card Interface
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MS3126F14-19SX | CONN PLUG 19POS STRAIGHT W/SCKT |
| 135-9701-201 | CONN MMCX RCPT VERT PCB .115LEG |
| VI-B0M-IX-F1 | CONVERTER MOD DC/DC 10V 75W |
| VI-B02-IX-F4 | CONVERTER MOD DC/DC 15V 75W |
| MAX1562ESA+T | IC CURR-LIM SW SNGL PROG 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS8113-KIT | 制造商:Maxim Integrated Products 功能描述:EMV EVALUATION KIT FOR THE DS8113 - Boxed Product (Development Kits) |
| DS8113-RNG+ | 功能描述:接口 - 专用 Smart Card Interface RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| DS8113-RNG+T&R | 制造商:Maxim Integrated Products 功能描述:DS8113 SMART CARD INT 28 SOIC LF T& - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC INTERFACE SMART CARD 28-SOIC |
| DS8113-RNG+T&R | 功能描述:接口 - 专用 Smart Card Interface RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| DS812 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。