- 您现在的位置：买卖IC网 > PDF目录11742 > DS8113-JNG+T&R (Maxim Integrated Products)IC INTERFACE SMART CARD 28-TSSOP PDF资料下载
参数资料
| 型号： | DS8113-JNG+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/17页 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE SMART CARD 28-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 智能卡 |
| 接口： | 模拟 |
| 电源电压： | 2.7 V ~ 6 V |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
Smart Card Power Select
The DS8113 supports three smart card VCC voltages:
1.8V, 3V, and 5V. The power select is controlled by the
1_8V and 5V/3V signals as shown in Table 3. The 1_8V
signal has priority over 5V/3V. When 1_8V is asserted
high, 1.8V is applied to VCC when the smart card is
active. When 1_8V is deasserted, 5V/3V dictates VCC
power range. VCC is 5V if 5V/3V is asserted to a logic-
high state, and VCC is 3V if 5V/3V is pulled to a
logic-low state. Care must be exercised when switching
from one VCC power selection to the other. If both 1_8V
and 5V/3V are high with CMDVCC high at the same
time, the DS8113 enters stop mode. To avoid acciden-
tal entry into stop mode, the state of 1_8V and 5V/3V
must not be changed simultaneously. A minimum delay
of 100ns should be observed between changing the
states of 1_8V and 5V/3V. See Figure 9 for the recom-
mended sequence of changing the VCC range.
DS8113
Smart Card Interface
______________________________________________________________________________________
15
VCC SELECT
STOP MODE
1.8V
3V
5V
1_8V
5V/3V
CMDVCC
Figure 9. Smart Card Power Select
Table 3. VCC Select and Operation Mode
1_8V
5V/3V
CMDVCC
VCC SELECT (V)
CARD INTERFACE STATUS
0
3
Activated
0
1
3
Inactivated
0
1
0
5
Activated
0
1
5
Inactivated
1
0
1.8
Activated
1
0
1
1.8
Inactivated
1
0
1.8
Reserved (Activated)
1
1.8
Not Applicable—Stop Mode
相关PDF资料 |
PDF描述 |
|---|---|
| MS3126F14-19SX | CONN PLUG 19POS STRAIGHT W/SCKT |
| 135-9701-201 | CONN MMCX RCPT VERT PCB .115LEG |
| VI-B0M-IX-F1 | CONVERTER MOD DC/DC 10V 75W |
| VI-B02-IX-F4 | CONVERTER MOD DC/DC 15V 75W |
| MAX1562ESA+T | IC CURR-LIM SW SNGL PROG 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS8113-KIT | 制造商:Maxim Integrated Products 功能描述:EMV EVALUATION KIT FOR THE DS8113 - Boxed Product (Development Kits) |
| DS8113-RNG+ | 功能描述:接口 - 专用 Smart Card Interface RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| DS8113-RNG+T&R | 制造商:Maxim Integrated Products 功能描述:DS8113 SMART CARD INT 28 SOIC LF T& - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC INTERFACE SMART CARD 28-SOIC |
| DS8113-RNG+T&R | 功能描述:接口 - 专用 Smart Card Interface RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| DS812 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。