- 您现在的位置：买卖IC网 > PDF目录1916 > DS8313-RRX+ (Maxim Integrated Products)IC INTERFACE SMART CARD 28-SOIC PDF资料下载
参数资料
| 型号： | DS8313-RRX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/18页 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE SMART CARD 28-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 243 |
| 应用： | 智能卡 |
| 接口： | 模拟 |
| 电源电压： | 2.7 V ~ 6 V |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
DS8313/DS8314
If the card is in the reader (if PRES is active), the host
microcontroller can begin an activation sequence (start
a card session) by pulling CMDVCC low. The following
events form an activation sequence (Figure 3):
1) CMDVCC is pulled low.
2) The internal oscillator changes to high frequency (t0).
3) The voltage generator is started (between t0 and t1).
4) VCC rises from 0 to 5V, 3V, or 1.8V with a con-
trolled slope (t2 = t1 + 1.5
× T). T is 64 times the
internal oscillator period (approximately 25s).
5) I/O pin is enabled (t3 = t1 + 4T) (they were previ-
ously pulled low).
6) The CLK signal is applied to the C3 contact (t4).
7) RST is enabled (t5 = t1 + 7T).
To apply the clock to the card interface:
1) Set RSTIN high.
2) Set CMDVCC low.
3) Set RSTIN low between t3 and t5; CLK will now start.
4) RST stays low until t5, then RST becomes the copy
of RSTIN.
5) RSTIN has no further effect on CLK after t5.
If the applied clock is not needed, set CMDVCC low
with RSTIN low. In this case, CLK starts at t3 (minimum
200ns after the transition on I/O, see Figure 4); after t5,
RSTIN can be set high to obtain an answer to request
(ATR) from an inserted smart card. Do not perform acti-
vation with RSTIN held permanently high.
Active Mode
When the activation sequence is completed, the card
interface is in active mode. The host microcontroller
and the smart card exchange data on the I/O lines.
Smart Card Interface
10
______________________________________________________________________________________
ATR
CMDVCC
RST
RSTIN
CLK
VCC
I/O
I/OIN
t0 t1
t2
t3
t4
t5 = tACT
Figure 3. Activation Sequence Using RSTIN and CMDVCC
相关PDF资料 |
PDF描述 |
|---|---|
| DS8500-JND+T&R | IC MODEM HART SGL 3.6V 20-TQFN |
| DS87C520-ENL | IC MCU EPROM/ROM 33MH IND 44TQFP |
| DS87C530-ECL+ | IC MCU EPR/ROM W/RTC 33MZ 52TQFP |
| DS87C530-KCL | IC MCU EPR/ROM W/RTC 33MZ 52CLCC |
| DS87C550-QCL+ | IC MCU EPROM ADC/PWM HS 68-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS8313-RRX+ | 功能描述:接口 - 专用 Smart Card Interface RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| DS8314 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Smart Card Interface |
| DS8314L-RRX+ | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Smart Card Interface |
| DS8314-RRX+ | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Smart Card Interface |
| DS833 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。