收藏本站
参数资料
型号： DSPIC30F3014-30I/ML
厂商： Microchip Technology
文件页数： 38/153页
文件大小： 0K
描述： IC DSPIC MCU/DSP 24K 44QFN
产品培训模块： Serial Communications using dsPIC30F I2C
Serial Communications using dsPIC30F SPI
Serial Communications using dsPIC30F UART
dsPIC30F 12 bit ADC - Part 2
dsPIC30F Addressing Modes - Part 1
dsPIC30F Architecture - Part 1
dsPIC30F DSP Engine & ALU
dsPIC30F Interrupts
dsPIC30F Motor Control PWM
dsPIC Timers
Asynchronous Stimulus
dsPIC30F Addressing Modes - Part 2
dsPIC30F Architecture - Part 2
dsPIC30F 12-bit ADC Part 1
标准包装： 45
系列： dsPIC™ 30F
核心处理器： dsPIC
芯体尺寸： 16-位
速度： 30 MIP
连通性： I²C，SPI，UART/USART
外围设备： 欠压检测/复位，POR，PWM，WDT
输入/输出数： 30
程序存储器容量： 24KB（8K x 24）
程序存储器类型： 闪存
EEPROM 大小： 1K x 8
RAM 容量： 2K x 8
电压 - 电源 (Vcc/Vdd)： 2.5 V ~ 5.5 V
数据转换器： A/D 13x12b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 44-VQFN 裸露焊盘
包装： 管件
产品目录页面： 651 (CN2011-ZH PDF)
配用： XLT44QFN2-ND - SOCKET TRAN ICE 44QFN/40DIP
AC164322-ND - MODULE SOCKET MPLAB PM3 28/44QFN
DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE
其它名称： DSPIC30F301430IML
dsPIC30F3014/4013
DS70138G-page 132
2010 Microchip Technology Inc.
19.1
A/D Result Buffer
The module contains a 16-word, dual port read-only
buffer, called ADCBUF0...ADCBUFF, to buffer the A/D
results. The RAM is 12 bits wide but the data obtained
is represented in one of four different 16-bit data for-
mats. The contents of the sixteen A/D Conversion
Result Buffer registers, ADCBUF0 through ADCBUFF,
cannot be written by user software.
19.2
Conversion Operation
After the A/D module has been configured, the sample
acquisition is started by setting the SAMP bit. Various
sources, such as a programmable bit, timer time-outs
and external events, terminate acquisition and start a
conversion. When the A/D conversion is complete, the
result is loaded into ADCBUF0...ADCBUFF, and the
DONE bit and the A/D Interrupt Flag, ADIF, are set after
the number of samples specified by the SMPI bit. The
ADC module can be configured for different interrupt
rates as described in Section 19.3 “Selecting the
Conversion Sequence”.
The following steps should be followed for doing an
A/D conversion:
1.
Configure the A/D module:
Configure analog pins, voltage reference and
digital I/O
Select A/D input channels
Select A/D conversion clock
Select A/D conversion trigger
Turn on A/D module
2.
Configure A/D interrupt (if required):
Clear ADIF bit
Select A/D interrupt priority
Set ADIE bit (for ISR processing)
3.
Start sampling
4.
Wait the required acquisition time
5.
Trigger acquisition end, start conversion:
6.
Wait for A/D conversion to complete, by either:
Waiting for the A/D interrupt, or
Waiting for the DONE bit to get set.
7.
Read A/D result buffer, clear ADIF if required
19.3
Selecting the Conversion Sequence
Several groups of control bits select the sequence in
which the A/D connects inputs to the sample/hold
channel, converts a channel, writes the buffer memory
and generates interrupts.
The sequence is controlled by the sampling clocks.
The SMPI bits select the number of acquisition/
conversion sequences that would be performed before
an interrupt occurs. This can vary from 1 sample per
interrupt to 16 samples per interrupt.
The BUFM bit splits the 16-word results buffer into two
8-word groups. Writing to the 8-word buffers is
alternated on each interrupt event.
Use of the BUFM bit depends on how much time is
available for moving the buffers after the interrupt.
If the processor can quickly unload a full buffer within
the time it takes to acquire and convert one channel,
the BUFM bit can be ‘0’ and up to 16 conversions (cor-
responding to the 16 input channels) may be done per
interrupt. The processor has one acquisition and
conversion time to move the sixteen conversions.
If the processor cannot unload the buffer within the
acquisition and conversion time, the BUFM bit should be
‘1’. For example, if SMPI<3:0> (ADCON2<5:2>) = 0111,
then eight conversions are loaded into 1/2 of the buffer,
following which an interrupt occurs. The next eight con-
versions are loaded into the other 1/2 of the buffer. The
processor has the entire time between interrupts to
move the eight conversions.
The ALTS bit can be used to alternate the inputs
selected during the sampling sequence. The input
multiplexer has two sets of sample inputs: MUX A and
MUX B. If the ALTS bit is ‘0’, only the MUX A inputs are
selected for sampling. If the ALTS bit is ‘1’ and
SMPI<3:0> = 0000 on the first sample/convert
sequence, the MUX A inputs are selected and on the
next acquire/convert sequence, the MUX B inputs are
selected.
The CSCNA bit (ADCON2<10>) allows the S/H input to
be sequentially scanned across a selected number of
analog inputs for the MUX A group. The inputs are
selected by the ADCSSL register. If a particular bit in
the ADCSSL register is ‘1’, the corresponding input is
selected. The inputs are always scanned from lower to
higher numbered inputs, starting after each interrupt. If
the number of inputs selected is greater than the
number of samples taken per interrupt, the higher
numbered inputs are unused.
Note:
The ADCHS, ADPCFG and ADCSSL reg-
isters allow the application to configure
AN13-AN15 as analog input pins. Since
these pins are not physically present on
the device, conversion results from these
pins read ‘0’.
相关PDF资料
PDF描述
ATMEGA168V-10MI IC AVR MCU 16K 10MHZ 32-QFN
PIC16F873A-I/SO IC MCU FLASH 4KX14 EE 28SOIC
PIC16F873A-I/SP IC MCU FLASH 4KX14 EE 28DIP
PIC32MX320F032H-40V/PT IC MCU 32BIT 32KB FLASH 64TQFP
ATMEGA3290-16AI IC AVR MCU 32K 16MHZ 100TQFP
相关代理商/技术参数
参数描述
dsPIC30F3014T-20E/ML 功能描述:数字信号处理器和控制器 - DSP, DSC 44LD 20MIPS 24 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC30F3014T-20E/PT 功能描述:数字信号处理器和控制器 - DSP, DSC 20MIPS 24 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F3014T-20I/ML 功能描述:IC DSPIC MCU/DSP 24K 44QFN RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:dsPIC™ 30F 产品培训模块:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 标准包装:22 系列:PIC® XLP™ 18F 核心处理器:PIC 芯体尺寸:8-位 速度:48MHz 连通性:I²C，SPI，UART/USART，USB 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:14 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:20-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
DSPIC30F3014T-20I/PT 功能描述:IC DSPIC MCU/DSP 24K 44TQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:dsPIC™ 30F 产品培训模块:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 标准包装:22 系列:PIC® XLP™ 18F 核心处理器:PIC 芯体尺寸:8-位 速度:48MHz 连通性:I²C，SPI，UART/USART，USB 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:14 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:20-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
dsPIC30F3014T-30I/ML 功能描述:数字信号处理器和控制器 - DSP, DSC 44LD 30MIPS 24 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*