- 您现在的位置：买卖IC网 > PDF目录97904 > EL5146CN 100 MHz Single Supply Rail to Rail Amplifier PDF资料下载
参数资料
| 型号： | EL5146CN |
| 英文描述： | 100 MHz Single Supply Rail to Rail Amplifier |
| 中文描述： | 100兆赫单电源轨至轨放大器 |
| 文件页数： | 7/20页 |
| 文件大小： | 945K |
| 代理商： | EL5146CN |
15
EL5144C, EL5146C, EL5244C, EL5246C,
EL5444C
100 MHz Single Supply Rail to Rail Amplifier
EL
5144C,
EL5146
C
,E
L
5244C,
EL
5246C,
EL5444C
Description of Operation and Applications Information
Product Description
The EL5144C series is a family of wide bandwidth, sin-
gle supply, low power, rail-to-rail output, voltage
feedback operational amplifiers. The family includes
single, dual, and quad configurations. The singles and
duals are available with a power down pin to reduce
power to 2.6A typically. All the amplifiers are inter-
nally compensated for closed loop feedback gains of +1
or greater. Larger gains are acceptable but bandwidth
will be reduced according to the familiar Gain-Band-
width Product.
Connected in voltage follower mode and driving a high
impedance load, the EL5144C series has a -3dB band-
width of 100 MHz. Driving a 150
load, they have a
-3dB bandwidth of 60 MHz while maintaining a 200
V/
S slew rate. The input common mode voltage range
includes ground while the output can swing rail to rail.
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high-frequency device, good printed circuit
board layout is necessary for optimum performance.
Ground plane construction is highly recommended.
Lead lengths should be as short as possible. The power
supply pin must be well bypassed to reduce the risk of
oscillation For normal single supply operation, where
the GND pin is connected to the ground plane, a single
4.7
F tantalum capacitor in parallel with a 0.1 F
ceramic capacitor from VS to GND will suffice. This
same capacitor combination should be placed at each
supply pin to ground if split supplies are to be used. In
this case, the GND pin becomes the negative supply rail.
For good AC performance, parasitic capacitance should
be kept to a minimum. Use of wire wound resistors
should be avoided because of their additional series
inductance. Use of sockets, particularly for the SO pack-
age, should be avoided if possible. Sockets add parasitic
inductance and capacitance that can result in compro-
mised performance.
Input, Output, and Supply Voltage Range
The EL5144C series has been designed to operate with a
single supply voltage of 5V. Split supplies can be used
so long as their total range is 5V.
The amplifiers have an input common mode voltage
range that includes the negative supply (GND pin) and
extends to within 1.5V of the positive supply (VS pin).
They are specified over this range.
The output of the EL5144C series amplifiers can swing
rail to rail.
As the load resistance becomes lower in
value, the ability to drive close to each rail is reduced.
However, even with an effective 150
load resistor
connected to a voltage halfway between the supply rails,
the output will swing to within 150mV of either rail.
相关PDF资料 |
PDF描述 |
|---|---|
| EL5146CS | 100 MHz Single Supply Rail to Rail Amplifier |
| EL5146C | 100 MHz Single Supply Rail to Rail Single Amplifier(100MHz单电源满幅度输出单路放大器) |
| EL5181C | 8ns High-Speed Comparator |
| EL5181CS-T13 | 8ns High-Speed Comparator |
| EL5181CS-T7 | 8ns High-Speed Comparator |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL5146CS | 功能描述:IC OP AMP 100MHZ R-R 8-SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| EL5146CS-T13 | 功能描述:IC AMP VFA SGL 100MHZ R-R 8-SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| EL5146CS-T7 | 功能描述:IC OP AMP R-R 100MHZ 8-SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| EL5146CSZ | 功能描述:IC AMP VFA SGL 100MHZ R-R 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| EL5146CSZ-T13 | 功能描述:IC AMP VFA SGL 100MHZ R-R 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。