- 您现在的位置：买卖IC网 > PDF目录97904 > EL5146CN 100 MHz Single Supply Rail to Rail Amplifier PDF资料下载
参数资料
| 型号： | EL5146CN |
| 英文描述： | 100 MHz Single Supply Rail to Rail Amplifier |
| 中文描述： | 100兆赫单电源轨至轨放大器 |
| 文件页数： | 9/20页 |
| 文件大小： | 945K |
| 代理商： | EL5146CN |
17
EL5144C, EL5146C, EL5244C, EL5246C,
EL5444C
100 MHz Single Supply Rail to Rail Amplifier
EL
5144C,
EL5146
C
,E
L
5244C,
EL
5246C,
EL5444C
loss which may be created by this additional resistor at
the output. Another method of reducing peaking is to
add a “snubber” circuit at the output. A snubber is a
resistor in a series with a capacitor, 150
and 100pF
being typical values. The advantage of a snubber is that
it does not draw DC load current.
When used as a cable driver, double termination is
always recommended for reflection-free performance.
For those applications, the back-termination series resis-
tor will de-couple the EL5144C series amplifier from the
cable and allow extensive capacitive drive. However,
other applications may have high capacitive loads with-
out a back-termination resistor. Again, a small series
resistor at the output can reduce peaking.
Disable / Power-Down
The EL5146C and EL5246C amplifiers can be disabled,
placing its output in a high-impedance state. Turn off
time is only 10 nsec and turn on time is around 500 nsec.
When disabled, the amplifier’s supply current is reduced
to 2.6A typically, thereby effectively eliminating
power consumption. The amplifier’s power down can be
controlled by standard TTL or CMOS signal levels at the
CE pin. The applied logic signal is relative to the GND
pin. Letting the CE pin float will enable the amplifier.
Hence, the 8 pin PDIP and SOIC single amps are pin
compatible with standard amplifiers that don’t have a
power down feature.
Short Circuit Current Limit
The EL5144C series amplifiers do not have internal
short circuit protection circuitry. Short circuit current of
90 mA sourcing and 65 mA sinking typically will flow if
the output is trying to drive high or low but is shorted to
half way between the rails. If an output is shorted indef-
initely, the power dissipation could easily increase such
that the part will be destroyed. Maximum reliability is
maintained if the output current never exceeds
±50mA.
This limit is set by internal metal interconnect limita-
tions. Obviously, short circuit conditions must not
remain or the internal metal connections will be
destroyed.
Power Dissipation
With the high output drive capability of the EL5144C
series amplifiers, it is possible to exceed the 150
°C
Absolute Maximum junction temperature under certain
load current conditions. Therefore, it is important to cal-
culate the maximum junction temperature for the
application to determine if load conditions or package
type need to be modified for the amplifier to remain in
the safe operating area.
The maximum power dissipation allowed in a package is
determined according to:
where:
TJMAX = Maximum Junction Temperature
TAMAX = Maximum Ambient Temperature
θJA = Thermal Resistance of the Package
PDMAX = Maximum Power Dissipation
in the Package.
The maximum power dissipation actually produced by
an IC is the total quiescent supply current times the total
power supply voltage, plus the power in the IC due to the
load, or:
where:
N = Number of amplifiers in the package
VS = Total Supply Voltage
PD
MAX
T
JM AX
T
AMAX
–
Θ
JA
----------------------------------------------
=
PD
MAX
NV
S
I
SMAX
V
(
S
V
OUT )
V
OUT
R
L
----------------
–
+
=
相关PDF资料 |
PDF描述 |
|---|---|
| EL5146CS | 100 MHz Single Supply Rail to Rail Amplifier |
| EL5146C | 100 MHz Single Supply Rail to Rail Single Amplifier(100MHz单电源满幅度输出单路放大器) |
| EL5181C | 8ns High-Speed Comparator |
| EL5181CS-T13 | 8ns High-Speed Comparator |
| EL5181CS-T7 | 8ns High-Speed Comparator |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL5146CS | 功能描述:IC OP AMP 100MHZ R-R 8-SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| EL5146CS-T13 | 功能描述:IC AMP VFA SGL 100MHZ R-R 8-SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| EL5146CS-T7 | 功能描述:IC OP AMP R-R 100MHZ 8-SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| EL5146CSZ | 功能描述:IC AMP VFA SGL 100MHZ R-R 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| EL5146CSZ-T13 | 功能描述:IC AMP VFA SGL 100MHZ R-R 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。