- 您现在的位置：买卖IC网 > PDF目录17322 > EL7532EVAL1Z (Intersil)EVALUATION BOARD FOR EL7532 PDF资料下载
参数资料
| 型号： | EL7532EVAL1Z |
| 厂商： | Intersil |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR EL7532 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 1.8V |
| 电流 - 输出： | 2A |
| 输入电压： | 2.5 ~ 5.5 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 1.5MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | EL7532 |
EL7532
recommended to be 22μF. Otherwise, if any of the above 3
conditions is not true, C 1 can remain as low as 10μF.
The RMS current present at the input capacitor is decided by
Equation 3:
Thermal Shut-Down
Once the junction reaches about +145°C, the regulator shuts
down. Both the P-Channel and the N-Channel MOSFETs
turn off. The output voltage will drop to zero. With the output
I INRMS = ------------------------------------------------ × I O
V O × ( V IN - V O )
V IN
(EQ. 3)
MOSFETs turned off, the regulator will soon cool down.
Once the junction temperature drops to about +130°C, the
regulator will restart again in the same manner as the EN pin
This is about half of the output current I O for all the V O . This
input capacitor must be able to handle this current.
The inductor peak-to-peak ripple current is given as:
connects to logic HI.
Thermal Performance
The EL7532 is in a fused-lead MSOP10 package. Compared
Δ I IL = --------------------------------------------
( V IN - V O ) × V O
L × V IN × f S
(EQ. 4)
to the regular MSOP10 package, the fused-lead package
provides lower thermal resistance. The typical θ JA of
+115°C/W (See Thermal Information section in spec table)
can be improved by maximizing the copper area around the
? L is the inductance
? f S the switching frequency (nominally 1.5MHz)
The inductor must be able to handle I O for the RMS load
current, and to assure that the inductor is reliable, it must
handle the 3A surge current that can occur during a current
limit condition.
In addition to decoupling capacitors and inductor value, it is
important to properly size the phase-lead capacitor C 4
(Refer to the Typical Application Diagram). The phase-lead
capacitor creates additional phase margin in the control loop
by generating a zero and a pole in the transfer function. As a
general rule of thumb, C 4 should be sized to start the phase-
lead at a frequency of ~2.5kHz. The zero will always appear
at lower frequency than the pole and follow Equation 5:
pins. A θ JA of +100°C/W can be achieved on a 4-layer board
and +125°C/W on a 2-layer board. Refer to Intersil’s Tech
Brief, TB379, for more information on thermal resistance.
Layout Considerations
The layout is very important for the converter to function
properly. The following PC layout guidelines should be
followed:
? Separate the Power Ground ( ) and Signal Ground ( );
connect them only at one point right at the pins
? Place the input capacitor as close to V IN and PGND pins
as possible
? Make the following PC traces as small as possible:
- from L X pin to L
f Z = ----------------------
1
2 π R 2 C 4
(EQ. 5)
- from C O to PGND
? If used, connect the trace from the FB pin to R 1 and R 2 as
close as possible
Over a normal range of R 2 (~10k to 100k), C 4 will range
from ~470pF to 4700pF. The pole frequency cannot be set
once the zero frequency is chosen as it is dictated by the
ratio of R 1 and R 2 , which is solely determined by the desired
output set point. Equation 6 shows the pole frequency
relationship:
? Maximize the copper area around the PGND pin
? Place several via holes under the chip to additional ground
plane to improve heat dissipation
The demo board is a good example of layout based on this
outline. Please refer to the EL7532 Application Brief.
f P = ---------------------------------------
1
2 π ( R 1 R 2 ) C 4
7
(EQ. 6)
FN7435.8
November 2, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| EEM12DRMI-S288 | CONN EDGECARD 24POS .156 EXTEND |
| AR4PJ-M3/87A | DIODE FAST REC 4A 600V SMPC |
| UDN2982A-T | IC SOURCE DRIVER 8CHAN 18-DIP |
| A9CCG-1408F | FLEX CABLE - AFG14G/AF14/AFG14G |
| EEM12DRSI-S288 | CONN EDGECARD 24POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL7532IY | 功能描述:IC REG BUCK SYNC ADJ 2A 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:3.3V 输入电压:4.5 V ~ 24 V PWM 型:- 频率 - 开关:- 电流 - 输出:125mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 包装:Digi-Reel® 供应商设备封装:SOT-6 其它名称:MAX1836EUT33#TG16DKR |
| EL7532IY-T13 | 功能描述:直流/直流开关调节器 EL7532IY MONOLITHIC 2A STP-DWNG RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| EL7532IY-T7 | 功能描述:IC REG BUCK SYNC ADJ 2A 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:3.3V 输入电压:4.5 V ~ 24 V PWM 型:- 频率 - 开关:- 电流 - 输出:125mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 包装:Digi-Reel® 供应商设备封装:SOT-6 其它名称:MAX1836EUT33#TG16DKR |
| EL7532IYZ | 功能描述:直流/直流开关调节器 EL7532IYZ MONOLITHIC 2A STP-DWNG RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| EL7532IYZ-T13 | 功能描述:直流/直流开关调节器 EL7532IYZ MONOLITHIC 2A STP-DWNG RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。