参数资料
| 型号： | EL7571CM |
| 厂商： | Intersil |
| 文件页数： | 9/19页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM PROGRAMMABLE 20SOIC |
| 标准包装： | 38 |
| 应用： | 控制器，Intel Pentium? II，Pro |
| 输入电压： | 4.5 V ~ 12.6 V |
| 输出数： | 2 |
| 输出电压： | 1.3 V ~ 3.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SO |
| 包装： | 管件 |
EL7571
1 MAX
P D = 1 OUTMAX × R 1
where:
I PEAK = peak ripple current
T ON = top switch on time
V IN = input voltage
F SW = switching frequency
V OUT = output voltage
I MIN = minimum load
Since inductance value tends to decrease with current,
ripple current will generally be greater than 21 MIN at higher
output current.
Once the minimum output inductance is determined, an off
the shelf inductor with current rating greater than the
maximum DC output required can be selected. Pulse
Engineering and Coil Craft are two manufactures of high
current inductors. For converter designers who want to
design their own high current inductors, for experimental
purposes or to further reduce costs, we recommend the
Micrometals Powered Iron Cores data sheet and
applications note as a good reference and starting point.
Current Sense Resistor, R 1
Inductor current is monitored indirectly via a low value
resistor R 1 . The voltage developed across the current sense
resistor is used to set the maximum operating current, the
current reversal threshold and the system load regulation. To
ensure reliable system operation it is important to sense the
actual voltage drop across the resistor. Accordingly a four
wire Kelvin connection should be made to the controller
current sense inputs. There are two criteria for selecting the
resistor value and type. Firstly, the minimum value is limited
by the maximum output current. The EL7571 current limit
capacitor has a typical threshold of 154mV, 125mV
minimum. When the voltage across the sense resistor
exceeds this threshold, the conduction cycle of the top
switch terminates immediately, providing pulse by pulse
current limiting. A resistor value must be selected which
guarantees operation under maximum load. That is:
V OCMIN
R 1 = -----------------------
where:
V OCMIN = minimum over current voltage threshold
I MAX = maximum output current
Secondly, since the load current passes directly through the
sense resistor, its power rating must be sufficient to handle
the power dissipated during maximum load (current limit)
conditions. Thus:
2
where:
P D = power dissipated in current sense resistor
P D must be less than the power rating of the current sense
resistor. High current applications may require parallel sense
resistors to dissipate sufficient power. Current Sense
Resistor Table below lists some popular current sense
resistors: the WLS-2512 series of Power Metal Strip
Resistors from Dale Electronics, OARS series Iron Alloy
resistor from IRC, and Copper Magnanin (CuNi) wire resistor
from Mills Resistors. Mother board copper trace is not
recommended because of its high temperature coefficient
and low power dissipation. The trade-off between the
different types of resistors are cost, space, packaging and
performance. Although Power Metal Strip Resistors are
relatively expensive, they are available in surface mount
packaging with tighter tolerances. Consequently, less board
space is used to achieve a more accurate current sense.
Alternatively, Magnanin copper wire has looser tolerance
and higher parasitic inductance. This results in a less current
sense but at a much lower cost. Metal track on the PCB can
also be used as current sense resistor. The trade-offs are
±30% tolerance and ±4000 ppm temperature coefficient.
Ultimately, the selection of the type of current sense element
must be made on an application by application basis.
Bill of Materials
TEMPERATURE
MANUFACTURER
Dale
IRC
Mills Resistor
PART NO.
WSL 2512
OARS Series
MRS1367-TBA
TOLERANCE
±1%
±5%
±10%
COEFFICIENT
±75ppm
±20ppm
±20ppm
POWER RATING
1W
1W - 5W
1.2W
PHONE NO.
402-563-6506
800-472-6467
916-422-5461
FAX NO.
402-563-6418
800-472-3282
906-422-1409
PCB Trace Resistor
±30%
±4000ppm
50A/in (1oz Cu)
9
相关PDF资料 |
PDF描述 |
|---|---|
| X5083V8-2.7A | IC SUPERVISOR CPU 8K EE 8-TSSOP |
| ASC20DRTN-S13 | CONN EDGECARD 40POS .100 EXTEND |
| X5083V8-2.7 | IC SUPERVISOR CPU 8K EE 8-TSSOP |
| GSA36DRSD-S664 | CONN EDGECARD 72POS DIP .125 SLD |
| X5083V8 | IC SUPERVISOR CPU 8K EE 8-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL7571CM-T13 | 功能描述:IC CTRLR PWM PROGRAMMABLE 20SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| EL7571CMZ | 功能描述:IC CTRLR PWM PROGRAMMABLE 20SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| EL7571CMZ-T13 | 功能描述:IC CTRLR PWM PROGRAMMABLE 20SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| EL7581 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:3-Channel DC-DC Converter |
| EL7581_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:3-Channel DC/DC Converter |
发布紧急采购，3分钟左右您将得到回复。