参数资料
| 型号： | EL8102IW-T7A |
| 厂商： | Intersil |
| 文件页数： | 2/15页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP 500MHZ R-R SOT-23-6 |
| 标准包装： | 250 |
| 放大器类型： | 电压反馈 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 600 V/µs |
| 增益带宽积： | 200MHz |
| -3db带宽： | 500MHz |
| 电流 - 输入偏压： | 6µA |
| 电压 - 输入偏移： | 800µV |
| 电流 - 电源： | 5.6mA |
| 电流 - 输出 / 通道： | 65mA |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 5 V，±1.5 V ~ 2.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 带卷 (TR) |
10
FN7104.7
August 10, 2007
output to eliminate most peaking. However, this will reduce
the gain slightly. If the gain setting is greater than 1, the gain
resistor RG can then be chosen to make up for any gain loss
which may be created by the additional series resistor at the
output.
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, a back-termination series resistor at the
amplifier’s output will isolate the amplifier from the cable and
allow extensive capacitive drive. However, other applications
may have high capacitive loads without a back-termination
resistor. Again, a small series resistor at the output can help
to reduce peaking.
Disable/Power-Down
The EL8102 can be disabled and its output placed in a high
impedance state. The turn-off time is about 25ns and the
turn-on time is about 200ns. When disabled, the amplifier’s
supply current is reduced to 30A typically, thereby
effectively eliminating the power consumption. The
amplifier’s power down can be controlled by standard TTL or
CMOS signal levels at the ENABLE pin. The applied logic
signal is relative to VS- pin. Letting the ENABLE pin float or
applying a signal that is less than 0.8V above VS- will enable
the amplifier. The amplifier will be disabled when the signal
at ENABLE pin is 2V above VS-.
Output Drive Capability
The EL8102, EL8103 do not have internal short circuit
protection circuitry. They have a typical short circuit current
of 80mA sourcing and 150mA sinking for the output is
connected to half way between the rails with a 10
Ω resistor.
If the output is shorted indefinitely, the power dissipation
could easily increase such that the part will be destroyed.
Maximum reliability is maintained if the output current never
exceeds ±40mA. This limit is set by the design of the internal
metal interconnections.
Power Dissipation
With the high output drive capability of the EL8102, EL8103,
It is possible to exceed the +125
°C absolute maximum
junction temperature under certain load current conditions.
Therefore, it is important to calculate the maximum junction
temperature for the application to determine if the load
conditions or package types need to be modified for the
amplifier to remain in the safe operating area.
The maximum power dissipation allowed in a package is
determined according to Equation 2:
Where:
TJMAX = Maximum junction temperature
TAMAX = Maximum ambient temperature
θ
JA = Thermal resistance of the package
The maximum power dissipation actually produced by an IC
is the total quiescent supply current times the total power
supply voltage, plus the power in the IC due to the load, or:
For sourcing, Equation 3:
For sinking, Equation 4:
Where:
VS = Total supply voltage
ISMAX = Maximum quiescent supply current
VOUT = Maximum output voltage of the application
RLOAD = Load resistance tied to ground
ILOAD = Load current
By setting the two PDMAX equations equal to each other, we
can solve the output current and RLOAD to avoid the device
overheat.
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, a good printed circuit
board layout is necessary for optimum performance. Lead
lengths should be as short as possible. The power supply
pin must be well bypassed to reduce the risk of oscillation.
For normal single supply operation, where the VS- pin is
connected to the ground plane, a single 4.7F tantalum
capacitor in parallel with a 0.1F ceramic capacitor from VS+
to GND will suffice. This same capacitor combination should
be placed at each supply pin to ground if split supplies are to
be used. In this case, the VS- pin becomes the negative
supply rail.
For good AC performance, parasitic capacitance should be
kept to a minimum. Use of wire wound resistors should be
avoided because of their additional series inductance. Use
of sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance that can result in
compromised performance. Minimizing parasitic capacitance
at the amplifier’s inverting input pin is very important. The
feedback resistor should be placed very close to the
inverting input pin. Strip line design techniques are
recommended for the signal traces.
PD
MAX
T
JMAX
T
AMAX
–
θ
JA
---------------------------------------------
=
(EQ. 2)
PD
MAX
V
S
I
SMAX
V
S
V
OUT
–
()
V
OUT
R
L
----------------
×
+
×
=
(EQ. 3)
PD
MAX
V
S
I
SMAX
V
OUT
V
S
-
–
() I
LOAD
×
+
×
=
(EQ. 4)
EL8102, EL8103
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2055CMS8#TRPBF | IC OPAMP ZERO DRFT DUAL LP 8MSOP |
| IXBOD1-20RD | IC DIODE MODULE BOD 0.2A 2000V |
| LTC2055CMS8#TR | IC OPAMP ZERO DRFT DUAL LP 8MSOP |
| IXBOD1-19RD | IC DIODE MODULE BOD 0.2A 1900V |
| EL8102IS-T7 | IC OP AMP 500MHZ R-R 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL8102IWZ-T7 | 功能描述:运算放大器 - 运放 EL8102IWZ 500MHZ R2R AMP RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| EL8102IWZ-T7A | 功能描述:运算放大器 - 运放 EL8102IWZ 500MHZ R2R AMP RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| EL8103 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:500MHz Rail-to-Rail Amplifiers |
| EL8103IW-T7 | 功能描述:IC OP AMP 500MHZ R-R SOT23-5 RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| EL8103IW-T7A | 功能描述:IC OP AMP 500MHZ R-R SOT-23-5 RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。