- 您现在的位置：买卖IC网 > PDF目录295883 > EN29LV320B-90BC (Eon Silicon Solution Inc.) 32 Megabit (4096K x 8-bit / 2048K x 16-bit) Flash Memory Boot Sector Flash Memory, CMOS 3.0 Volt-only PDF资料下载
参数资料
| 型号： | EN29LV320B-90BC |
| 厂商： | Eon Silicon Solution Inc. |
| 英文描述： | 32 Megabit (4096K x 8-bit / 2048K x 16-bit) Flash Memory Boot Sector Flash Memory, CMOS 3.0 Volt-only |
| 中文描述： | 32兆位（4096K × 8位/ 2048K x 16位）闪存引导扇区闪存，CMOS 3.0伏，只 |
| 文件页数： | 16/49页 |
| 文件大小： | 437K |
| 代理商： | EN29LV320B-90BC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
This Data Sheet may be revised by subsequent versions
2004 Eon Silicon Solution, Inc., www.essi.com.tw
or modifications due to changes in technical specifications.
23
EN29LV320
Rev. E, Issue Date: 2006/05/16
DATA# Polling must be performed at any address within a sector that is being programmed or
erased and not a protected sector. Otherwise, DATA# polling may give an inaccurate result if the
address used is in a protected sector.
Just prior to the completion of the embedded operations, DQ7 may change asynchronously when
the output enable (OE#) is low. This means that the device is driving status information on DQ7 at
one instant of time and valid data at the next instant of time. Depending on the time the system
samples the DQ7 output, it may read the status of valid data. Even if the device has completed the
embedded operation and DQ7 has a valid data, the data output on DQ0-DQ6 may be still invalid.
The valid data on DQ0-DQ7 should be read on the subsequent read attempts.
The flowchart for DATA# Polling (DQ7) is shown on Flowchart 5. The DATA# Polling (DQ7) timing
diagram is shown in Figure 6.
RY/BY#: Ready/Busy Status output
The RY/BY# is a dedicated, open-drain output pin that indicates whether an Embedded Algorithm is
in progress or completed. The RY/BY# status is valid after the rising edge of the final WE# pulse in
the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied
together in parallel with a pull-up resistor to Vcc.
In the output-low period, signifying Busy, the device is actively erasing or programming. This
includes programming in the Erase Suspend mode. If the output is high, signifying the Ready, the
device is ready to read array data (including during the Erase Suspend mode), or is in the standby
mode.
DQ6: Toggle Bit I
The EN29LV320 provides a “Toggle Bit” on DQ6 to indicate the status of the embedded
programming and erase operations. (See Table 10)
During an embedded Program or Erase operation, successive attempts to read data from the device
at any address (by active OE# or CE#) will result in DQ6 toggling between “zero” and “one”. Once
the embedded Program or Erase operation is completed, DQ6 will stop toggling and valid data will
be read on the next successive attempts. During Programming, the Toggle Bit is valid after the rising
edge of the fourth WE# pulse in the four-cycle sequence. During Erase operation, the Toggle Bit is
valid after the rising edge of the sixth WE# pulse for sector erase or chip erase.
In embedded programming, if the sector being written to is protected, DQ6 will toggles for about 2
s,
then stop toggling without the data in the sector having changed. In Sector Erase or Chip Erase, if all
selected sectors are protected, DQ6 will toggle for about 100
s. The chip will then return to the read
mode without changing data in all protected sectors.
The flowchart for the Toggle Bit (DQ6) is shown in Flowchart 6. The Toggle Bit timing diagram is
shown in Figure 7.
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count
limit. Under these conditions DQ5 produces a “1.” This is a failure condition that indicates the
program or erase cycle was not successfully completed. Since it is possible that DQ5 can become a
1 when the device has successfully completed its operation and has returned to read mode, the user
must check again to see if the DQ6 is toggling after detecting a “1” on DQ5.
The DQ5 failure condition may appear if the system tries to program a “1” to a location that is
previously programmed to “0.” Only an erase operation can change a “0” back to a “1.” Under
this condition, the device halts the operation, and when the operation has exceeded the timing limits,
相关PDF资料 |
PDF描述 |
|---|---|
| EN29LV320B-90BIP | 32 Megabit (4096K x 8-bit / 2048K x 16-bit) Flash Memory Boot Sector Flash Memory, CMOS 3.0 Volt-only |
| EN29LV320B-90BI | 32 Megabit (4096K x 8-bit / 2048K x 16-bit) Flash Memory Boot Sector Flash Memory, CMOS 3.0 Volt-only |
| EN29LV320B-90TC | 32 Megabit (4096K x 8-bit / 2048K x 16-bit) Flash Memory Boot Sector Flash Memory, CMOS 3.0 Volt-only |
| EN3 | GLASS FILLED POLYETHYLENE POLYMER, FEMALE; MALE, CIRCULAR CONNECTOR, CRIMP; SOLDER |
| EN3I2F16PAGK | 2 CONTACT(S), FEMALE, CIRCULAR CONNECTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EN29LV320BT-70TIP | 制造商:EON SILICON SOLUTION INC 功能描述:32M TOP BOOT TSOP |
| EN29LV320CT-70TIP | 制造商:EON SILICON SOLUTION INC 功能描述:32M Parallel Flash, x8/x16, 70ns, TSOP48 |
| EN29LV400AB-70TCP | 制造商:EON SILICON SOLUTION INC 功能描述:EN29LV400A Series, 4 Mbit (512 K x 8) 70 NS 48 TSOP 3 V Bottom Boot NOR Flash |
| EN29LV400AB-70TIP | 制造商:EON SILICON SOLUTION INC 功能描述:EN29LV400A Series 4 Mbit (512 K x 8) 70 NS 48 TSOP 3 V Bottom Boot NOR Flash |
| EN29LV400AT-70TCP | 制造商:EON SILICON SOLUTION INC 功能描述:4 Mb PAR NOR 512Kx8bit/256Kx16bit 3V 48-TSOP |
发布紧急采购，3分钟左右您将得到回复。