- 您现在的位置：买卖IC网 > PDF目录362743 > EPC1213 (Electronic Theatre Controls, Inc.) Configuration Devices for SRAM-Based LUT Devices PDF资料下载
参数资料
| 型号： | EPC1213 |
| 厂商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Configuration Devices for SRAM-Based LUT Devices |
| 中文描述： | 配置SRAM器件基于LUT的器件 |
| 文件页数： | 10/28页 |
| 文件大小： | 380K |
| 代理商： | EPC1213 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
10
Altera Corporation
Configuration Devices for ACEX, APEX, FLEX & Mercury Devices Data Sheet
Notes:
(1)
(2)
(3)
This package is available for EPC1 and EPC1441 devices only.
This package is available for EPC2 and EPC1441 devices only.
The
OE
,
nCS
, and
nINIT_CONF
pins on EPC2 devices have internal, user-configurable 1-k
pull-up resistors. If
internal pull-up resistors are used, external pull-up resistors should not be used on these pins.
The EPC1441 device does not support data cascading. EPC2 and EPC1 devices support data cascading.
This pin applies to the EPC2 device only.
(4)
(5)
nINIT_CONF
(3)
,
(5)
–
13
16
Open-
Drain
Output
Allows the INIT_CONF JTAG instruction to initiate
configuration. This pin is connected to the
nCONFIG
pin
of the ACEX, APEX, FLEX or Mercury device to initiate
configuration from the EPC2 via a JTAG instruction. If
multiple EPC2 devices are used to configure an ACEX,
APEX, FLEX or Mercury device, only the first EPC2 has
its
nINIT_CONF
pin tied to the device
’
s
nCONFIG
pin.
JTAG data input pin. Connect this pin to V
CC
if the
JTAG circuitry is not used.
JTAG data output pin. Do not connect this pin if the
JTAG circuitry is not used.
JTAG mode select pin. Connect this pin to V
CC
if the
JTAG circuitry is not used.
JTAG clock pin. Connect this pin to ground if the JTAG
circuitry is not used.
Mode select for V
CC
supply.
VCCSEL
must be
connected to ground if the device uses a 5.0-V power
supply (i.e., V
CC
= 5.0 V).
VCCSEL
must be connected
to V
CC
if the device uses a 3.3-V power supply (i.e.,
V
CC
= 3.3 V).
Mode select for
VPP
.
VPPSEL
must be connected to
ground if
VPP
uses a 5.0-V power supply
(i.e.,
VPP
= 5.0 V).
VPPSEL
must be connected to V
CC
if
VPP
uses a 3.3-V power supply (i.e,
VPP
= 3.3 V).
Programming power pin. For the EPC2 device, this pin
is normally tied to V
CC
. If the EPC2 V
CC
is 3.3 V,
VPP
can be tied to 5.0 V to improve in-system programming
times. For EPC1 and EPC1441 devices,
VPP
must be
tied to V
CC
.
Power pin.
Ground Ground pin. A 0.2-
μ
F decoupling capacitor must be
placed between the
VCC
and
GND
pins.
TDI
(5)
–
11
13
Input
TDO
(5)
–
1
28
Output
TMS
(5)
–
19
25
Input
TCK
(5)
–
3
32
Input
VCCSEL
(5)
–
5
3
Input
VPPSEL
(5)
–
14
17
Input
VPP
(5)
–
18
23
Power
VCC
7, 8
5
20
10
27
12
Power
GND
Table 4. EPC2, EPC1, & EPC1441 Pin Functions During ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000 &
Mercury Configuration (Part 2 of 2)
Pin Name
Pin Number
Pin
Type
Description
8-Pin
PDIP
(1)
20-Pin
PLCC
32-Pin
TQFP
(2)
相关PDF资料 |
PDF描述 |
|---|---|
| EPC1441 | Configuration Devices for SRAM-Based LUT Devices |
| EPC1064 | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
| EPC1064V | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
| EPC1213 | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
| EPC1441 | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPC1213DM8 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| EPC1213LC20 | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 212Kb 6 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC1213LC-20 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configuration EPROM |
| EPC1213LI20 | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 212Kb 6 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC1213LI-20 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configuration EPROM |
发布紧急采购，3分钟左右您将得到回复。