收藏本站
参数资料
型号： EPC1213
厂商： Electronic Theatre Controls, Inc.
英文描述： Configuration Devices for SRAM-Based LUT Devices
中文描述： 配置SRAM器件基于LUT的器件
文件页数： 13/28页
文件大小： 380K
代理商： EPC1213
Altera Corporation
13
Configuration Devices for ACEX, APEX, FLEX & Mercury Devices Data Sheet
Figure 6. Two ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, or Mercury Devices Configured with Two EPC2 or
EPC1 Configuration Devices
Notes:
(1)
(2)
The pull-up resistor should be connected to the same supply voltage as the configuration device.
The diagram shows an ACEX 1K, APEX 20K, FLEX 10K, or Mercury device, which has
MSEL0
and
MSEL1
tied to
ground. For FLEX 6000 devices,
MSEL
is tied to ground, and the
DATA0
pin is named
DATA
. EPC2 cannot be used
with FLEX 6000 devices. All other connections are the same for ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, and
Mercury devices.
All pull-up resistors are 1 k
(APEX 20KE pull-resistors are 10k
). The
OE
and
nCS
pins on EPC2 devices have
internal, user-configurable 1-k
pull-up resistors. If internal pull-up resistors are used, external pull-up resistors
should not be used on these pins.
The
nINIT_CONF
pin is only available on EPC2 devices and has an internal pull up of 1 k
that is always active. If
nINIT_CONF
is not available or not used,
nCONFIG
must be pulled to V
CC
either directly or through a 1-k
resistor.
(3)
(4)
f
For more information on ACEX 1K, APEX 20K, FLEX 10K, or FLEX 6000
Application Note116 (Configuring ACEX 1K,
.
FLEX 8000 Device Configuration
FLEX 8000 devices differ from ACEX 1K, APEX 20K, FLEX 10K, and
FLEX 6000 devices in that they have internal oscillators that can provide a
DCLK
signal to the configuration device. The configuration device sends
configuration data out as a serial bitstream on the
DATA
output pin. This
data is routed into the FLEX 8000 device via the
DATA0
input pin. The
EPC1, EPC1441, EPC1213, EPC1064, and EPC1064V configuration devices
support this type of configuration.
Configuration
Device 1
DCLK
DATA
OE
nCS
nINIT_CONF (4)
DCLK
DATA0
nSTATUS
CONF_DONE
nCONFIG
VCC
VCC
GND
GND
nCE
DCLK
DATA
nCS
OE
Configuration
Device 2
MSEL0
MSEL1
DCLK
DATA0
nSTATUS
CONF_DONE
nCONFIG
GND
nCE
MSEL0
MSEL1
nCEO
(2)
(2)
(1)
(1)
nCASC
ACEX 1K, APEX 20K, FLEX 10K,
FLEX 6000 or Mercury Device (3)
ACEX 1K, APEX 20K
FLEX 10K, FLEX 6000
or Mercury Device (3)
相关PDF资料
PDF描述
EPC1441 Configuration Devices for SRAM-Based LUT Devices
EPC1064 Configuration Devices for ACEX, APEX, FLEX & Mercury Devices
EPC1064V Configuration Devices for ACEX, APEX, FLEX & Mercury Devices
EPC1213 Configuration Devices for ACEX, APEX, FLEX & Mercury Devices
EPC1441 Configuration Devices for ACEX, APEX, FLEX & Mercury Devices
相关代理商/技术参数
参数描述
EPC1213DM8 制造商:Rochester Electronics LLC 功能描述:- Bulk
EPC1213LC20 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 212Kb 6 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20
EPC1213LC-20 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configuration EPROM
EPC1213LI20 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 212Kb 6 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20
EPC1213LI-20 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configuration EPROM
发布紧急采购，3分钟左右您将得到回复。