- 您现在的位置：买卖IC网 > PDF目录362744 > EPC1213 (Altera Corporation) Configuration Devices for ACEX, APEX, FLEX & Mercury Devices PDF资料下载
参数资料
| 型号： | EPC1213 |
| 厂商： | Altera Corporation |
| 英文描述： | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
| 中文描述： | 配置器件ACEX，顶点，柔性 |
| 文件页数： | 7/28页 |
| 文件大小： | 380K |
| 代理商： | EPC1213 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Altera Corporation
7
Configuration Devices for ACEX, APEX, FLEX & Mercury Devices Data Sheet
Device
Configuration
The control signals for configuration devices
—
nCS
,
OE
, and
DCLK
—
interface directly with ACEX, APEX, FLEX, and Mercury device control
signals. All ACEX, APEX, FLEX, and Mercury devices can be configured
by a configuration device without requiring an external intelligent
controller.
The configuration device
’
s
OE
and
nCS
pins control the tri-state buffer on
the
DATA
output pin, and enable the address counter (and the oscillator in
EPC2, EPC1, and EPC1441 devices). When
OE
is driven low, the
configuration device resets the address counter and tri-states its
DATA
pin.
The
nCS
pin controls the output of the configuration device. If
nCS
is held
high after the
OE
reset pulse, the counter is disabled and the
DATA
output
pin is tri-stated. When
nCS
is driven low, the counter and
DATA
output pin
are enabled. When
OE
is driven low again, the address counter is reset and
the
DATA
output pin is tri-stated, regardless of the state of
nCS
.
1
The EPC2, EPC1, and EPC1441 devices determine the operation
mode and whether the ACEX 1K, APEX 20K, FLEX 10K,
FLEX 8000, FLEX 6000, or Mercury protocols should be used
when
OE
is driven high.
When the configuration device has driven out all of its data and has
driven
nCASC
low, the device tri-states the
DATA
pin to avoid contention
with other configuration devices.
The EPC2 device allows the user to initiate configuration of the ACEX,
APEX, FLEX, or Mercury device via an additional pin,
nINIT_CONF
, that
can be tied to the
nCONFIG
pin of the ACEX, APEX, FLEX, or Mercury
device(s) to be configured. A JTAG instruction causes the EPC2 device to
drive
nINIT_CONF
low, which in turn pulls
nCONFIG
low. The EPC2
device then drives
nINIT_CONF
high to start configuration. When the
JTAG state machine exits this state,
nINIT_CONF
releases
nCONFIG
and
configuration is initiated.
1
An EPC2 device can be programmed with a POF generated for
an EPC1 or EPC1441 device, however, an EPC2 device cannot
configure FLEX 6000 or FLEX 8000 devices. An EPC1 device can
be programmed using a POF
generated for an EPC1441 device.
相关PDF资料 |
PDF描述 |
|---|---|
| EPC1441 | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
| EPC4xxx | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC16QC100 | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC16QI100 | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC8xxx | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPC1213DM8 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| EPC1213LC20 | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 212Kb 6 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC1213LC-20 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configuration EPROM |
| EPC1213LI20 | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 212Kb 6 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC1213LI-20 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configuration EPROM |
发布紧急采购，3分钟左右您将得到回复。