- 您现在的位置：买卖IC网 > PDF目录362744 > EPC1213 (Altera Corporation) Configuration Devices for ACEX, APEX, FLEX & Mercury Devices PDF资料下载
参数资料
| 型号： | EPC1213 |
| 厂商： | Altera Corporation |
| 英文描述： | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
| 中文描述： | 配置器件ACEX，顶点，柔性 |
| 文件页数： | 8/28页 |
| 文件大小： | 380K |
| 代理商： | EPC1213 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
8
Altera Corporation
Configuration Devices for ACEX, APEX, FLEX & Mercury Devices Data Sheet
ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000 & Mercury Device
Configuration
ACEX 1K, APEX 20K, FLEX 10K, and Mercury devices can be configured
with EPC2, EPC1, or EPC1441 devices. FLEX 6000 devices can be
configured with EPC1 or EPC1441 devices. The EPC2, EPC1, or EPC1441
device stores configuration data in its EPROM array and serially clocks
data out with an internal oscillator. The
OE
,
nCS
, and
DCLK
pins supply
the control signals for the address counter and the output tri-state buffer.
The configuration device sends a serial bitstream of configuration data to
its
DATA
pin, which is routed to the
DATA0
or
DATA
input pin on the
ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, or Mercury device.
Figure4
shows an ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, or Mercury device
configured with a single EPC2, EPC1, or EPC1441 device.
Figure 4. ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, or Mercury Device
Configured with an EPC2, EPC1, or EPC1441 Configuration Device
Table4
describes EPC2, EPC1, and EPC1441 pin functions during
ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, and Mercury device
configuration.
ACEX 1K, APEX 20K, FLEX 10K,
FLEX 6000, or Mercury Device (2)
Configuration
Device
DCLK
DATA
OE
nCS
nINIT_CONF (4)
MSEL0
MSEL1
DCLK
DATA0
nSTATUS
CONF_DONE
nCONFIG
VCC
VCC
GND
GND
(3)
(3)
nCE
(1)
(1)
Notes:
(1)
The pull-up resistor should be connected to the same supply voltage as the
configuration device.
The diagram shows an ACEX 1K, APEX 20K, FLEX 10K or Mercury device, which
has
MSEL0
and
MSEL1
tied to ground. For FLEX 6000 devices,
MSEL
is tied to
ground, and the
DATA0
pin is named
DATA
. EPC2 cannot be used with FLEX 6000
devices. All other connections are the same for ACEX 1K, APEX 20K, FLEX 10K,
FLEX 6000 and Mercury devices.
All pull-up resistors are 1 k
. APEX 20KE pull up resistors are 10 k
. The
OE
,
nCS
,
and
nINIT_CONF
pins on EPC2 devices have internal, user-configurable 1-k
pull-up resistors. If internal pull-up resistors are used, external pull-up resistors
should not be used on these pins.
The
nINIT_CONF
pin is only available on EPC2 devices and has an internal pull up
of 1 k
that is always active. If
nINIT_CONF
is not available or not used,
nCONFIG
must be pulled to V
CC
either directly or through a 1-k
resistor.
(2)
(3)
(4)
相关PDF资料 |
PDF描述 |
|---|---|
| EPC1441 | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
| EPC4xxx | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC16QC100 | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC16QI100 | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC8xxx | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPC1213DM8 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| EPC1213LC20 | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 212Kb 6 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC1213LC-20 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configuration EPROM |
| EPC1213LI20 | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 212Kb 6 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC1213LI-20 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configuration EPROM |
发布紧急采购，3分钟左右您将得到回复。