参数资料
型号: EPM7192SQC160-10F
厂商: Altera
文件页数: 49/66页
文件大小: 0K
描述: IC MAX 7000 CPLD 192 160-PQFP
标准包装: 24
系列: MAX® 7000
可编程类型: 系统内可编程
最大延迟时间 tpd(1): 10.0ns
电压电源 - 内部: 4.75 V ~ 5.25 V
逻辑元件/逻辑块数目: 12
宏单元数: 192
门数: 3750
输入/输出数: 124
工作温度: 0°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 160-BQFP
供应商设备封装: 160-PQFP(28x28)
包装: 托盘
Altera Corporation
53
MAX 7000 Programmable Logic Device Family Data Sheet
Notes to tables:
(1)
These values are specified under the recommended operating conditions shown in Table 14. See Figure 13 for more
information on switching waveforms.
(2)
This minimum pulse width for preset and clear applies for both global clear and array controls. The tLPA parameter
must be added to this minimum width if the clear or reset signal incorporates the tLAD parameter into the signal
path.
(3)
This parameter is a guideline that is sample-tested only and is based on extensive device characterization. This
parameter applies for both global and array clocking.
(4)
These parameters are measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.
(5)
The fMAX values represent the highest frequency for pipelined data.
(6)
Operating conditions: VCCIO = 3.3 V ± 10% for commercial and industrial use.
(7)
For EPM7064S-5, EPM7064S-6, EPM7128S-6, EPM7160S-6, EPM7160S-7, EPM7192S-7, and EPM7256S-7 devices,
these values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these
devices, add an additional 0.1 ns to the PIA timing value.
(8)
The tLPA parameter must be added to the tLAD, tLAC, tIC, tEN, tSEXP, tACL, and tCPPW parameters for macrocells
running in the low-power mode.
Power
Consumption
Supply power (P) versus frequency (fMAX in MHz) for MAX 7000 devices
is calculated with the following equation:
P = PINT + PIO = ICCINT × VCC + PIO
The PIO value, which depends on the device output load characteristics
and switching frequency, can be calculated using the guidelines given in
The ICCINT value, which depends on the switching frequency and the
application logic, is calculated with the following equation:
ICCINT =
A × MCTON + B × (MCDEV – MCTON) + C × MCUSED × fMAX × togLC
The parameters in this equation are shown below:
MCTON
= Number of macrocells with the Turbo Bit option turned on,
as reported in the MAX+PLUS II Report File (.rpt)
MCDEV
= Number of macrocells in the device
MCUSED = Total number of macrocells in the design, as reported
in the MAX+PLUS II Report File (.rpt)
fMAX
= Highest clock frequency to the device
togLC
= Average ratio of logic cells toggling at each clock
(typically 0.125)
A, B, C
= Constants, shown in Table 39
相关PDF资料
PDF描述
GSM06DTMH-S189 CONN EDGECARD 12POS R/A .156 SLD
EEC13DRXS CONN EDGECARD 26POS DIP .100 SLD
ISPLSI 5512VA-70LB388I IC PLD ISP 288I/O 15NS 388BGA
ASC30DRTI-S93 CONN EDGECARD 60POS DIP .100 SLD
180-062-203L001 CONN DB62 FEML HD SLD CUP NICKEL
相关代理商/技术参数
参数描述
EPM7192SQC160-10N 功能描述:CPLD - 复杂可编程逻辑器件 CPLD - MAX 7000 192 Macro 124 IOs RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100
EPM7192SQC160-15 功能描述:CPLD - 复杂可编程逻辑器件 CPLD - MAX 7000 192 Macro 124 IOs RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100
EPM7192SQC160-15F 功能描述:IC MAX 7000 CPLD 192 160-PQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - CPLD(复杂可编程逻辑器件) 系列:MAX® 7000 标准包装:24 系列:CoolRunner II 可编程类型:系统内可编程 最大延迟时间 tpd(1):7.1ns 电压电源 - 内部:1.7 V ~ 1.9 V 逻辑元件/逻辑块数目:24 宏单元数:384 门数:9000 输入/输出数:173 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:208-BFQFP 供应商设备封装:208-PQFP(28x28) 包装:托盘
EPM7192SQC160-15N 功能描述:CPLD - 复杂可编程逻辑器件 CPLD - MAX 7000 192 Macro 124 IOs RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100
EPM7192SQC160-7 功能描述:CPLD - 复杂可编程逻辑器件 CPLD - MAX 7000 192 Macro 124 IOs RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100