- 您现在的位置：买卖IC网 > PDF目录17075 > EVAL-AD5372EBZ (Analog Devices Inc)BOARD EVAL FOR AD5372 PDF资料下载
参数资料
| 型号： | EVAL-AD5372EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/29页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5372 |
| 产品培训模块： | DAC Architectures |
| 标准包装： | 1 |
| DAC 的数量： | 32 |
| 位数： | 16 |
| 采样率（每秒）： | 540k |
| 数据接口： | 串行 |
| 设置时间： | 20µs |
| DAC 型： | 电压 |
| 工作温度： | -40°C ~ 85°C |
| 已供物品： | 板，CD |
| 已用 IC / 零件： | AD5372 |
| 相关产品： | AD5372BSTZ-REEL-ND - IC DAC 16BIT 32CH SER 64-LQFP AD5372BSTZ-ND - IC DAC 16BIT 32CH SER 64-LQFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD5372/AD5373
Rev. C | Page 18 of 28
The required reference levels can be calculated as follows:
1.
Identify the nominal output range on VOUT.
2.
Identify the maximum offset span and the maximum gain
required on the full output signal range.
3.
Calculate the new maximum output range on VOUT,
including the expected maximum offset and gain errors.
4.
Choose the new required VOUTMAX and VOUTMIN,
keeping the VOUT limits centered on the nominal values.
Note that VDD and VSS must provide sufficient headroom.
5.
Calculate the value of VREF as follows:
VREF = (VOUTMAX – VOUTMIN)/4
Reference Selection Example
If
Nominal output range = 12 V (4 V to +8 V)
Zero-scale error = ±70 mV
Gain error = ±3%, and
SIGGNDx = AGND = 0 V
Then
Gain error = ±3%
=> Maximum positive gain error = 3%
=> Output range including gain error = 12 + 0.03(12) = 12.36 V
Zero-scale error = ±70 mV
=> Maximum offset error span = 2(70 mV) = 0.14 V
=> Output range including gain error and zero-scale error =
12.36 V + 0.14 V = 12.5 V
VREF calculation
Actual output range = 12.5 V, that is, 4.25 V to +8.25 V;
VREF = (8.25 V + 4.25 V)/4 = 3.125 V
If the solution yields an inconvenient reference level, the user
can adopt one of the following approaches:
Use a resistor divider to divide down a convenient, higher
reference level to the required level.
Select a convenient reference level above VREF and modify
the gain and offset registers to digitally downsize the reference.
In this way, the user can use almost any convenient reference
level but can reduce the performance by overcompaction of
the transfer function.
Use a combination of these two approaches.
CALIBRATION
The user can perform a system calibration on the AD5372/
AD5373 to reduce gain and offset errors to below 1 LSB. This
reduction is achieved by calculating new values for the M and C
registers and reprogramming them.
The M and C registers should not be programmed until both
the zero-scale and full-scale errors are calculated.
Reducing Zero-Scale Error
Zero-scale error can be reduced as follows:
1.
Set the output to the lowest possible value.
2.
Measure the actual output voltage and compare it to the
required value. This gives the zero-scale error.
3.
Calculate the number of LSBs equivalent to the error and
add this number to the default value of the C register. Note
that only negative zero-scale error can be reduced.
Reducing Full-Scale Error
Full-scale error can be reduced as follows:
1.
Measure the zero-scale error.
2.
Set the output to the highest possible value.
3.
Measure the actual output voltage and compare it to the
required value. Add this error to the zero-scale error. This
is the span error, which includes the full-scale error.
4.
Calculate the number of LSBs equivalent to the span error
and subtract this number from the default value of the M
register. Note that only positive full-scale error can be
reduced.
AD5372 Calibration Example
This example assumes that a 4 V to +8 V output is required.
The DAC output is set to 4 V but is measured at 4.03 V. This
gives a zero-scale error of 30 mV.
1 LSB = 12 V/65,536 = 183.105 μV
30 mV = 164 LSBs
The full-scale error can now be calculated. The output is set to
8 V and a value of 8.02 V is measured. This gives a full-scale
error of +20 mV and a span error of +20 mV – (–30 mV) =
+50 mV.
50 mV = 273 LSBs
The errors can now be removed as follows:
1.
Add 164 LSBs to the default C register value:
(32,768 + 164) = 32,932
2.
Subtract 273 LSBs from the default M register value:
(65,535 273) = 65,262
3.
Program the M register to 65,262; program the C register
to 32,932.
相关PDF资料 |
PDF描述 |
|---|---|
| EVAL-AD5361EBZ | BOARD EVAL FOR AD5361 |
| V300C2E50BF3 | CONVERTER MOD DC/DC 2V 50W |
| 0210490910 | CABLE JUMPER 1.25MM .178M 21POS |
| V24C5E125BL2 | CONVERTER MOD DC/DC 5V 125W |
| EVAL-AD5433EBZ | BOARD EVAL FOR AD5433 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5373EBZ | 功能描述:BOARD EVAL FOR AD5373 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5379EB | 制造商:AD 制造商全称:Analog Devices 功能描述:40-Channel, 14-Bit, Parallel and Serial Input, Bipolar Voltage-Output DAC |
| EVAL-AD5379EBZ | 功能描述:BOARD EVALUATION FOR AD5379 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5380EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD5380EBZ | 功能描述:BOARD EVAL FOR AD5380 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。