- 您现在的位置：买卖IC网 > PDF目录17103 > EVAL-AD5755-1SDZ (Analog Devices Inc)BOARD EVAL FOR AD5755-1 PDF资料下载
参数资料
| 型号： | EVAL-AD5755-1SDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 33/52页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5755-1 |
| 视频文件： | AD5755: 16-Bit Multi-Channel, Voltage and Current Output DAC |
| 标准包装： | 1 |
| DAC 的数量： | 4 |
| 位数： | 16 |
| 数据接口： | 串行 |
| 设置时间： | 11µs |
| DAC 型： | 电流/电压 |
| 工作温度： | -40°C ~ 105°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
Data Sheet
AD5755-1
Rev. E | Page 39 of 52
Status Register
The status register is a read only register. This register contains
any fault information as a well as a ramp active bit and a user
toggle bit. When the STATREAD bit in the main control
register is set, the status register contents can be read back on
the SDO pin during every write sequence. Alternatively, if the
STATREAD bit is not set, the status register can be read using
the normal readback operation.
Table 29. Decoding the Status Register
MSB
LSB
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
DC-
DCD
DC-
DCC
DC-
DCB
DC-
DCA
User
toggle
PEC
error
Ramp
active
Over
TEMP
VOUT_D
fault
VOUT_C
fault
VOUT_B
fault
VOUT_A
fault
IOUT_D
fault
IOUT_C
fault
IOUT_B
fault
IOUT_A
fault
Table 30. Status Register Options
Bit
Description
DC-DCD
In current output mode, this bit is set on Channel D if the dc-to-dc converter cannot maintain compliance (it may be
reaching its V
MAX voltage). In this case, the IOUT_D fault bit is also set. See the DC-to-DC Converter VMAX Functionality section
for more information on this bit’s operation under this condition.
In voltage output mode, this bit is set if, on Channel D, the dc-to-dc converter is unable to regulate to 15 V as expected.
When this bit is set, it does not result in the FAULT pin going high.
DC-DCC
In current output mode, this bit is set on Channel C if the dc-to-dc converter cannot maintain compliance (it may be
reaching its V
MAX voltage). In this case, the IOUT_C fault bit is also set. See the DC-to-DC Converter VMAX Functionality section for
more information on this bit’s operation under this condition.
In voltage output mode, this bit is set if, on Channel C, the dc-to-dc converter is unable to regulate to 15 V as expected.
When this bit is set, it does not result in the FAULT pin going high.
DC-DCB
In current output mode, this bit is set on Channel B if the dc-to-dc converter cannot maintain compliance (it may be
reaching its V
MAX voltage). In this case, the IOUT_B fault bit is also set. See the DC-to-DC Converter VMAX Functionality section for
more information on this bit’s operation under this condition.
In voltage output mode, this bit is set if, on Channel B, the dc-to-dc converter is unable to regulate to 15 V as expected.
When this bit is set, it does not result in the FAULT pin going high.
DC-DCA
In current output mode, this bit is set on Channel A if the dc-to-dc converter cannot maintain compliance (it may be
reaching its V
MAX voltage). In this case, the IOUT_A fault bit is also set. See the DC-to-DC Converter VMAX Functionality section for
more information on this bit’s operation under this condition.
In voltage output mode, this bit is set if, on Channel A, the dc-to-dc converter is unable to regulate to 15 V as expected.
When this bit is set, it does not result in the FAULT pin going high.
User Toggle
User toggle bit. This bit is set or cleared via the software register. This can be used to verify data communications if needed.
PEC Error
Denotes a PEC error on the last data-word received over the SPI interface.
Ramp Active
This bit is set while any one of the output channels is slewing (slew rate control is enabled on at least one channel).
Over TEMP
This bit is set if the AD5755-1 core temperature exceeds approximately 150°C.
V
OUT_D Fault
This bit is set if a fault is detected on the V
OUT_D pin.
V
OUT_C Fault
This bit is set if a fault is detected on the V
OUT_C pin.
V
OUT_B Fault
This bit is set if a fault is detected on the V
OUT_B pin.
V
OUT_A Fault
This bit is set if a fault is detected on the V
OUT_A pin.
I
OUT_D Fault
This bit is set if a fault is detected on the I
OUT_D pin.
I
OUT_C Fault
This bit is set if a fault is detected on the I
OUT_C pin.
I
OUT_B Fault
This bit is set if a fault is detected on the I
OUT_B pin.
I
OUT_A Fault
This bit is set if a fault is detected on the I
OUT_A pin.
相关PDF资料 |
PDF描述 |
|---|---|
| R-7215D | CONV DC/DC 2A 19-28VIN 15V |
| VE-J14-EZ | CONVERTER MOD DC/DC 48V 25W |
| R-7212P | CONV DC/DC 2A 15-28VIN 12V |
| R-7212D | CONV DC/DC 2A 15-28VIN 12V |
| VI-JVX-EZ | CONVERTER MOD DC/DC 5.2V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5755SDZ | 功能描述:BOARD EVAL FOR AD5755 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5757SDZ | 功能描述:BOARD EVAL FOR AD5757 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5760SDZ | 功能描述:BOARD EVAL FOR AD5760SDZ RoHS:否 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5764EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR QUAD, 16-BIT, HIGH ACCURACY, SERIAL INPUT, BIPOLAR VOLTAGE OUTPUT DAC 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk |
| EVAL-AD5764EBZ | 功能描述:BOARD EVAL FOR AD5764 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。