- 您现在的位置：买卖IC网 > PDF目录17060 > EVAL-AD7356EDZ (Analog Devices Inc)BOARD EVAL AD7356 PDF资料下载
参数资料
| 型号： | EVAL-AD7356EDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/21页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL AD7356 |
| 标准包装： | 1 |
| ADC 的数量： | 2 |
| 位数： | 12 |
| 采样率（每秒）： | 5M |
| 数据接口： | 串行 |
| 输入范围： | ±VREF/2 |
| 在以下条件下的电源（标准）： | 36mW @ 5MSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7356 |
| 已供物品： | 板，CD |
AD7356
Rev. A | Page 17 of 20
POWER-UP TIMES
The AD7356 has two power-down modes: partial power-down
and full power-down, which are described in detail in the Normal
sections. This section deals with the power-up time required
when coming out of any of these modes. Note that the recom-
mended decoupling capacitors must be in place on the REFA
and REFB pins for the power-up times to apply.
To power up from partial power-down mode, one dummy cycle
is required. The device is fully powered up after approximately
200 ns have elapsed from the falling edge of CS. When the
partial power-up time has elapsed, the ADC is fully powered
up, and the input signal is acquired properly. The quiet time,
tQUIET, must still be allowed from the point where the bus goes
back into three-state after the dummy conversion to the next
falling edge of CS.
To power up from full power-down mode, approximately 6 ms
should be allowed from the falling edge of CS, shown in
as tPOWER-UP2.
Note that during power-up from partial power-down mode, the
track-and-hold, which is in hold mode while the part is powered
down, returns to track mode after the first SCLK edge that the
part receives after the falling edge of CS.
When power supplies are first applied to the AD7356, the ADC
can power up in either of the power-down modes or in normal
mode. Because of this, it is best to allow a dummy cycle to elapse
to ensure that the part is fully powered up before attempting a
valid conversion. Likewise, if the part is to be kept in partial
power-down mode immediately after the supplies are applied,
then two dummy cycles must be initiated. The first dummy
cycle must hold CS low until after the 10th SCLK falling edge; in
the second cycle, CS must be brought high between the second
and 10th SCLK falling edges (see
).
Alternatively, if the part is to be placed into full power-down
mode when the supplies are applied, three dummy cycles must
be initiated. The first dummy cycle must hold CS low until after
the 10th SCLK falling edge; the second and third dummy cycles
place the part into full power-down mode (see
and
the
section).
POWER vs. THROUGHPUT RATE
The power consumption of the AD7356 varies with the
throughput rate. When using very slow throughput rates
and as fast an SCLK frequency as possible, the various power-
down options can be used to make significant power savings.
However, the AD7356 quiescent current is low enough that
even without using the power-down options, there is a noticeable
variation in power consumption with sampling rate. This is true
whether a fixed SCLK value is used or it is scaled with the
sampling rate. Figure 29 shows a plot of power vs. throughput rate
when operating in normal mode for a fixed maximum SCLK
frequency and a SCLK frequency that scales with the sampling
rate. The internal reference was used for Figure 29.
10
14
18
22
26
30
34
38
0
1000
2000
5000
3000
4000
P
O
WE
R
(
m
W)
THROUGHPUT (kSPS)
065
05
-030
80MHz SCLK
VARIABLE SCLK
Figure 29. Power vs. Throughput Rate
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2009YM6 TR | IC DISTRIBUTION SW ADJ SOT23-6 |
| 0210391030 | CABLE JUMPER 1MM .030M 33POS |
| EVAL-AD7352EDZ | BOARD EVAL AD7352 |
| 0210390949 | CABLE JUMPER 1MM .102M 25POS |
| 0210390948 | CABLE JUMPER 1MM .102M 25POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7357EDZ | 功能描述:BOARD EVAL FOR AD7357 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7366CBZ | 功能描述:BOARD EVALUATION FOR AD7366 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:iCMOS® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7366SDZ | 功能描述:BOARD EVAL FOR AD7366 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:iCMOS® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7367CBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:True Bipolar Input, Dual 1 レs, 12-/14-Bit, 2-Channel SAR ADCs |
| EVAL-AD7367SDZ | 功能描述:数据转换 IC 开发工具 EVALUATION CONTROL BOARD I.C. RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
发布紧急采购，3分钟左右您将得到回复。