- 您现在的位置：买卖IC网 > PDF目录17056 > EVAL-AD7366CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7366 PDF资料下载
参数资料
| 型号： | EVAL-AD7366CBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/29页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD7366 |
| 标准包装： | 1 |
| 系列： | iCMOS® |
| ADC 的数量： | 2 |
| 位数： | 12 |
| 采样率（每秒）： | 1M |
| 数据接口： | 串行 |
| 输入范围： | ±10 V |
| 在以下条件下的电源（标准）： | 70mW @ 1MSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7366 |
| 已供物品： | 板 |
| 相关产品： | AD7366BRUZ-5-ND - IC ADC 12BIT DUAL 500KSPS 24-TSS AD7366BRUZ-5500RL7-ND - IC ADC 12BIT DUAL BIPO 24-TSSOP AD7366BRUZ-5-RL7-ND - IC ADC 12BIT DUAL BIPO 24-TSSOP AD7366BRUZ-ND - IC ADC 12BIT SAR 1MSPS 24TSSOP AD7366BRUZ-RL7-ND - IC ADC 12BIT SAR 1MSPS 24TSSOP AD7366BRUZ-500RL7-ND - IC ADC 12BIT SAR 1MSPS 24TSSOP |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD7366/AD7367
Rev. D | Page 14 of 28
TERMINOLOGY
Differential Nonlinearity (DNL)
DNL is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
Integral Nonlinearity (INL)
INL is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale, a point 1 LSB
below the first code transition, and full scale, a point 1 LSB above
the last code transition.
Zero Code Error
The deviation of the midscale transition (all 1s to all 0s) from
the ideal VIN voltage, that is, AGND LSB for bipolar ranges
and 2 × VREF 1 LSB for the unipolar range.
Positive Full-Scale Error
The deviation of the last code transition (011…110) to (011…111)
from the ideal (that is, +4 × VREF 1 LSB or +2 × VREF – 1 LSB)
after the zero code error has been factored out.
Negative Full-Scale Error
The deviation of the first code transition (10…000) to (10…001)
from the ideal (that is, 4 × VREF + 1 LSB, 2 × VREF + 1 LSB, or
AGND + 1 LSB) after the zero code error has been factored out.
Zero Code Error Match
The difference in zero code error across all channels.
Positive Full-Scale Error Match
The difference in positive full-scale error across all channels.
Negative Full-Scale Error Match
The difference in negative full-scale error across all channels.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of a conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within ± LSB, after the end of a conversion.
Signal-to-Noise (+ Distortion) Ratio (SINAD)
This ratio is the measured ratio of signal-to-noise (+ distortion)
at the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent on the number of quantization levels in the digitiza-
tion process: the more levels, the smaller the quantization noise.
The theoretical signal-to-noise (+ distortion) ratio for an ideal
N-bit converter with a sine wave input is as follows:
Signal-to-Noise (+ Distortion) = (6.02N + 1.76) dB
Thus, for a 12-bit converter, the SINAD is 74 dB.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the fundamental.
For the AD7366/AD7367, THD is defined as follows:
1
6
5
4
3
2
V
THD
2
log
20
)
dB
(
+
=
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through the sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic, or spurious noise, is the ratio of the rms value
of the next largest component in the ADC output spectrum
(up to fS/2, excluding dc) to the rms value of the fundamental.
Normally, the value of this specification is determined by the
largest harmonic in the spectrum. However, for ADCs where
the harmonics are buried in the noise floor, it is a noise peak.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of cross-
talk between any two channels when operating in any of the
input ranges. It is measured by applying a full-scale, 150 kHz
sine wave signal to all unselected input channels and determining
how much that signal is attenuated in the selected channel with
a 50 kHz signal. The figure given is the typical value across all
four channels for the AD7366/AD7367 (see Figure 9 for more
information).
Intermodulation Distortion (IMD)
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion prod-
ucts at the sum, and different frequencies of mfa ± nfb, where
m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms
are those for which neither m nor n is equal to zero. For example,
the second-order terms include (fa + fb) and (fa fb), and the
third-order terms include (2fa + fb), (2fa fb), (fa + 2fb), and
(fa 2fb).
The AD7366/AD7367 are tested using the CCIF standard where
two input frequencies near the top end of the input bandwidth
are used. In this case, the second-order terms are usually distanced
in frequency from the original sine waves, and the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification, where it is the ratio of the rms
sum of the individual distortion products to the rms amplitude
of the sum of the fundamentals expressed in decibels.
相关PDF资料 |
PDF描述 |
|---|---|
| PCX1H470MCL1GS | CAP ALUM 47UF 50V 20% SMD |
| 0210490886 | CABLE JUMPER 1.25MM .152M 19POS |
| MIC2017YM6 TR | IC SW DISTRIBUTION ADJ SOT23-6 |
| EEM28DTKN | CONN EDGECARD 56POS DIP .156 SLD |
| 0210391074 | CABLE JUMPER 1MM .030M 37POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7366SDZ | 功能描述:BOARD EVAL FOR AD7366 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:iCMOS® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7367CBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:True Bipolar Input, Dual 1 レs, 12-/14-Bit, 2-Channel SAR ADCs |
| EVAL-AD7367SDZ | 功能描述:数据转换 IC 开发工具 EVALUATION CONTROL BOARD I.C. RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| EVAL-AD7376EBZ | 功能描述:BOARD EVAL FOR AD7376 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD7400AEBZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
发布紧急采购，3分钟左右您将得到回复。