- 您现在的位置：买卖IC网 > PDF目录17038 > EVAL-AD7610CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7610 PDF资料下载
参数资料
| 型号： | EVAL-AD7610CBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD7610 |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 250k |
| 数据接口： | 串行，并联 |
| 在以下条件下的电源（标准）： | 90mW @ 250kSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7610 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD7610
Data Sheet
Rev. A | Page 20 of 32
DRIVER AMPLIFIER CHOICE
Although the AD7610 is easy to drive, the driver amplifier must
meet the following requirements:
For multichannel, multiplexed applications, the driver
amplifier and the AD7610 analog input circuit must be
able to settle for a full-scale step of the capacitor array at a
16-bit level (0.0015%). For the amplifier, settling at 0.1% to
0.01% is more commonly specified. This differs significantly
from the settling time at a 16-bit level and should be verified
prior to driver selection. The AD8021 op amp combines ultra-
low noise and high gain bandwidth and meets this settling
time requirement even when used with gains of up to 13.
The noise generated by the driver amplifier needs to be
kept as low as possible to preserve the SNR and transition
noise performance of the AD7610. The noise coming from
the driver is filtered by the external 1-pole low-pass filter
as shown in Figure 27. The SNR degradation due to the
amplifier is
(
)
π
+
=
2
3
2
log
20
N
dB
NADC
LOSS
Ne
f
V
SNR
where:
VNADC is the noise of the ADC, which is:
20
10
2
SNR
INp-p
NADC
V
=
f–3dB is the cutoff frequency of the input filter (3.9 MHz).
N is the noise factor of the amplifier (+1 in buffer
configuration).
eN is the equivalent input voltage noise density of the op
amp, in nV/√Hz.
The driver needs to have a THD performance suitable to
that of the AD7610. Figure 15 shows the THD vs. frequency
that the driver should exceed.
The AD8021 meets these requirements and is appropriate for
almost all applications. The AD8021 needs a 10 pF external
compensation capacitor that should have good linearity as an
NPO ceramic or mica type. Moreover, the use of a noninverting
+1 gain arrangement is recommended and helps to obtain the
best signal-to-noise ratio.
The AD8022 can also be used when a dual version is needed
and a gain of 1 is present. The AD829 is an alternative in appli-
cations where high frequency (above 100 kHz) performance is not
required. In applications with a gain of 1, an 82 pF compensation
capacitor is required. The AD8610 is an option when low bias
current is needed in low frequency applications.
Since the AD7610 uses a large geometry, high voltage input
switch, the best linearity performance is obtained when using
the amplifier at its maximum full power bandwidth. Gaining
the amplifier to make use of the more dynamic range of the
ADC results in increased linearity errors. For applications
requiring more resolution, the use of an additional amplifier
with gain should precede a unity follower driving the AD7610.
See Table 8 for a list of recommended op amps.
Table 8. Recommended Driver Amplifiers
Amplifier
Typical Application
12 V supply, very low noise, low distortion,
low power, low frequency
±15 V supplies, very low noise, low frequency
±12 V supplies, very low noise, high frequency
±12 V supplies, very low noise, high
frequency, dual
±13 V supplies, low bias current, low
frequency, single/dual
VOLTAGE REFERENCE INPUT/OUTPUT
The AD7610 allows the choice of either a very low temperature
drift internal voltage reference, an external reference or an external
buffered reference.
The internal reference of the AD7610 provides excellent perfor-
mance and can be used in almost all applications. However, the
linearity performance is guaranteed only with an external reference.
相关PDF资料 |
PDF描述 |
|---|---|
| EVAL-AD7651CBZ | BOARD EVALUATION FOR AD7651 |
| EVAL-AD7694CBZ | BOARD EVALUATION FOR AD7694 |
| 0210490994 | CABLE JUMPER 1.25MM .127M 29POS |
| RBC08DREH-S93 | CONN EDGECARD 16POS .100 EYELET |
| EVAL-AD7684CBZ | BOARD EVALUATION FOR AD7684 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7610EDZ | 功能描述:BOARD EVAL FOR AD7610 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7612CB | 制造商:Analog Devices 功能描述:EVAL BD FOR AD7612 - Bulk |
| EVAL-AD7612CBZ | 功能描述:BOARD EVALUATION FOR AD7612 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7612EDZ | 功能描述:BOARD EVAL FOR AD7612 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7621CB2 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 2 LSB INL, 3 MSPS PulSAR?? ADC |
发布紧急采购，3分钟左右您将得到回复。