参数资料
型号: EVAL-AD7657-1EDZ
厂商: Analog Devices Inc
文件页数: 15/32页
文件大小: 0K
描述: BOARD EVAL CONTROL AD7657-1
标准包装: 1
系列: iCMOS®
ADC 的数量: 6
位数: 14
采样率(每秒): 250k
数据接口: 串行,并联
输入范围: ±10 V
在以下条件下的电源(标准): 140mW @ 250kSPS
工作温度: -40°C ~ 85°C
已用 IC / 零件: AD7657-1
已供物品:
相关产品: AD7657YSTZ-1-RL-ND - IC ADC 14BIT 6CH 250KSPS 64LQFP
AD7657YSTZ-1-ND - IC ADC 14BIT 6CH 250KSPS 64LQFP
AD7657BSTZ-1-RL-ND - IC ADC 14BIT 6CH 250KSPS 64LQFP
AD7657BSTZ-1-ND - IC ADC 14BIT 6CH 250KSPS 64LQFP
AD7657YSTZ-REEL-ND - IC ADC 14BIT 6CH 250KSPS 64LQFP
AD7657YSTZ-ND - IC ADC 14BIT 6CH 250KSPS 64LQFP
AD7657BSTZ-ND - IC ADC 14BIT 6CH 250KSPS 64-LQFP
AD7657BSTZ-REEL-ND - IC ADC 14BIT 6CH 250KSPS 64-LQFP
AD7656-1/AD7657-1/AD7658-1
Data Sheet
Rev. D | Page 22 of 32
+
DVCC
+
DVCC
AVCC
AGND
DGND
VDRIVE DGND
VDD
AGND
+
VSS
AGND
+
REFCAPA, B, C
AGND
REFIN/OUT
AGND
D0 TO D15
CONVST A, B, C
CS
RD
BUSY
SER/PAR
H/S
W/B
RANGE
RESET
STBY
VDRIVE
AD7656-1/
AD7657-1/
AD7658-1
1F
P/C/DSP
1F
DIGITAL SUPPLY
VOLTAGE +3V OR +5V
ANA L OG SUPPLY
VOLTAGE 5V
1SEE POWER SUPPLY CONFIGURATION SECTION.
+9.5V TO +16.5V1
SUPPLY
2.5V
REF
SIX ANALOG
INPUTS
–9.5V TO –16.5V1
SUPPLY
PARALLEL
INTERFACE
07017-
026
Figure 28. Typical Connection Diagram
The VDRIVE supply is connected to the same supply as the
processor. The voltage on VDRIVE controls the voltage value of
the output logic signals.
Decouple the VDD and VSS signals with a minimum 1 F
decoupling capacitor. These supplies are used for the high voltage
analog input structures on the AD7656-1/AD7657-1/AD7658-1
analog inputs.
DRIVING THE ANALOG INPUTS
Together, the driver amplifier and the analog input circuit used
for the AD7656-1 must settle for a full-scale step input to a 16-bit
level (0.0015%), which is within the specified 550 ns acquisition
time of the AD7656-1. The noise generated by the driver
amplifier needs to be kept as low as possible to preserve the
SNR and transition noise performance of the AD7656-1. In
addition, the driver also needs to have a THD performance
suitable for the AD7656-1.
The AD8021 meets these requirements. The AD8021 needs an
external compensation capacitor of 10 pF. If a dual version of
the AD8021 is required, the AD8022 can be used. The AD8610
and the AD797 can also be used to drive the AD7656-1/AD7657-1/
AD7658-1.
INTERFACE OPTIONS
The AD7656-1/AD7657-1/AD7658-1 provide two interface
options: a high speed parallel interface and a high speed serial
interface. The required interface mode is selected via the
SER/PAR SEL pin. The parallel interface can operate in word
(W/B = 0) or byte (W/B = 1) mode. When in serial mode, the
AD7656-1/AD7657-1/AD7658-1 can be configured into daisy-
chain mode.
When in parallel mode, a read operation only accesses the
results related to conversions which have just occurred. For
example, consider the case where CONVST A and CONVST C
are toggled simultaneously but CONVST B is not used. At
end of the conversion process when BUSY goes low a read is
implemented. Four read pulses (in parallel mode) are applied
and data from V1, V2, V5, and V6 are output. Data from V3
and V4 is not output since CONVST B was not toggled in this
cycle. However, when in serial mode all zeros are output in
place of the ADC result for ADCs not included in the conversion
cycle. See the Serial Interface section for more information.
Parallel Interface (SER/PAR SEL = 0)
The AD7656-1/AD7657-1/AD7658-1 consist of six 16-/14-/
12-bit ADCs, respectively. A simultaneous sample of all six
ADCs can be performed by connecting all three CONVST
pins (CONVST A, CONVST B, and CONVST C) together. The
AD7656-1/AD7657-1/AD7658-1 need to see a CONVST pulse
to initiate a conversion; this should consist of a falling CONVST
edge followed by a rising CONVST edge. The rising edge of
CONVST initiates simultaneous conversions on the selected
ADCs. The AD7656-1/AD7657-1/AD7658-1 each contain an
on-chip oscillator that is used to perform the conversions. The
conversion time, tCONV, is 3 s. The BUSY signal goes low to
indicate the end of a conversion. The falling edge of the BUSY
signal is used to place the track-and-hold amplifier into track mode.
The AD7656-1/AD7657-1/AD7658-1 also allow the six ADCs
to be converted simultaneously in pairs by pulsing the three
CONVST pins independently. CONVST A is used to initiate
simultaneous conversions on V1 and V2, CONVST B is used to
initiate simultaneous conversions on V3 and V4, and CONVST C
is used to initiate simultaneous conversions on V5 and V6. The
conversion results from the simultaneously sampled ADCs are
stored in the output data registers. Note that once a rising edge
occurs on any one CONVST pin to initiate a conversion, then any
相关PDF资料
PDF描述
VI-B71-EY CONVERTER MOD DC/DC 12V 50W
PCMC135T-1R0MF COIL 1.0 UH POWER CHOKE 20% SMD
SDR0703-680KL INDUCTOR POWER 68UH SMD
EVAL-AD7656-1EDZ BOARD EVAL CONTROL AD7656-1
VI-B70-EY CONVERTER MOD DC/DC 5V 50W
相关代理商/技术参数
参数描述
EVAL-AD7657CBZ 功能描述:BOARD EVAL FOR AD7657 RoHS:是 类别:编程器,开发系统 >> 评估板 - 模数转换器 (ADC) 系列:iCMOS® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率(每秒):94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源(标准):- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,软件
EVAL-AD7658-1EDZ 制造商:AD 制造商全称:Analog Devices 功能描述:250 kSPS, 6-Channel, Simultaneous Sampling, Bipolar, 16-/14-/12-Bit ADC
EVAL-AD7658-1SDZ 功能描述:数据转换 IC 开发工具 Evaluation Control Board RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V
EVAL-AD7658CBZ 功能描述:BOARD EVAL FOR AD7658 RoHS:是 类别:编程器,开发系统 >> 评估板 - 模数转换器 (ADC) 系列:iCMOS® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率(每秒):94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源(标准):- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,软件
EVAL-AD7660CB 制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board AD766X/AD767X