- 您现在的位置：买卖IC网 > PDF目录17045 > EVAL-AD7678CBZ (Analog Devices Inc)BOARD EVAL FOR AD7678 PDF资料下载
参数资料
| 型号： | EVAL-AD7678CBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/28页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD7678 |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| ADC 的数量： | 1 |
| 位数： | 18 |
| 采样率（每秒）： | 100k |
| 数据接口： | 串行，并联 |
| 输入范围： | ±VREF |
| 在以下条件下的电源（标准）： | 31mW @ 100kSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7678 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7678
Rev. A | Page 17 of 28
TYPICAL CONNECTION DIAGRAM
Figure 21 shows a typical connection diagram for the AD7678.
Different circuitry shown on this diagram is optional and is
discussed later in this data sheet.
Analog Inputs
Figure 22 shows a simplified analog input section of the
AD7678. The diodes shown in Figure 22 provide ESD protec-
tion for the inputs. Care must be taken to ensure that the analog
input signal never exceeds the absolute ratings on these inputs.
This will cause these diodes to become forward-biased and start
conducting current. These diodes can handle a forward-biased
current of 120 mA max. This condition could eventually occur
when the input buffer’s U1 or U2 supplies are different from
AVDD. In such a case, an input buffer with a short-circuit
current limitation can be used to protect the part.
IN+
IN–
AGND
AVDD
R+ = 3k
CS
R– = 3k
03084-0-028
Figure 22. Simplified Analog Input
This analog input structure is a true differential structure. By
using these differential inputs, signals common to both inputs
are rejected as shown in Figure 23, which represents typical
CMRR over frequency.
FREQUECY (kHz)
80
CMRR
(dB)
75
50
100
1000
10000
110
70
65
60
55
03084-0-029
Figure 23. Analog Input CMRR vs. Frequency
During the acquisition phase for ac signals, the AD7678 behaves
like a 1-pole RC filter consisting of the equivalent resistance,
R+, R–, and CS. Resistors R+ and R– are typically 3 k and are
lumped components made up of a serial resistor and the on
resistance of the switches. CS is typically 60 pF and mainly
consists of the ADC sampling capacitor. This 1-pole filter with a
–3 dB cutoff frequency of 900 kHz typ reduces any undesirable
aliasing effect and limits the noise coming from the inputs.
Because the input impedance of the AD7678 is very high, the
part can be driven directly by a low impedance source without
gain error.
Driver Amplifier Choice
Although the AD7678 is easy to drive, the driver amplifier
needs to meet the following requirements:
The driver amplifier and the AD7678 analog input circuit
have to be able to settle for a full-scale step of the capacitor
array at an 18-bit level (0.0004%). In the amplifier’s data
sheet, settling at 0.1% or 0.01% is more commonly
specified. This could differ significantly from the settling
time at an 18-bit level and, therefore, should be verified
prior to driver selection. The tiny op amp AD8021, which
combines ultralow noise and high gain-bandwidth, meets
this settling time requirement.
The noise generated by the driver amplifier needs to be
kept as low as possible in order to preserve the SNR and
transition noise performance of the AD7678. The noise
coming from the driver is filtered by the AD7678 analog
input circuit 1-pole low-pass filter made by R+, R–, and CS.
The SNR degradation due to the amplifier is
2
)
(
625
25
log
20
N
3dB
–
LOSS
Ne
f
SNR
where:
f–3dB
is the –3 dB input bandwidth in MHz of the AD7678
(0.9 MHz).
N
is the noise factor of the amplifiers (1 if in buffer
configuration).
eN
is the equivalent input noise voltage of each op amp in
nV/Hz.
For instance, for a driver with an equivalent input noise of
6 nV/Hz (e.g., AD8610) configured as a buffer, thus with
a noise gain of +1, the SNR degrades by only 0.65 dB.
The driver needs to have a THD performance suitable to
that of the AD7678.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BWV-EY | CONVERTER MOD DC/DC 5.8V 50W |
| 0210391012 | CABLE JUMPER 1MM .076M 31POS |
| VE-BWT-EY | CONVERTER MOD DC/DC 6.5V 50W |
| VE-BWR-EY | CONVERTER MOD DC/DC 7.5V 50W |
| EVAL-AD7634EDZ | BOARD EVAL FOR AD7634 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7678EDZ | 功能描述:BOARD EVAL FOR AD7678 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7679CB | 制造商:Rochester Electronics LLC 功能描述:AD7679 EVAL BOARD 18BIT 570KSPS ADC - Bulk 制造商:Analog Devices 功能描述:AD7679 EVAL BOARD 18BIT 570KSPS ADC |
| EVAL-AD7679CBZ | 功能描述:BOARD EVALUATION FOR AD7679 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7679EDZ | 功能描述:BOARD EVAL FOR AD7679 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD767XCB | 制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board AD766X/AD767X |
发布紧急采购，3分钟左右您将得到回复。