- 您现在的位置：买卖IC网 > PDF目录17053 > EVAL-AD7920CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7920 PDF资料下载
参数资料
| 型号： | EVAL-AD7920CBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD7920 |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 250k |
| 数据接口： | 串行 |
| 输入范围： | 0 ~ Vdd |
| 在以下条件下的电源（标准）： | 12.5mW @ 250kSPS，5V |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7920 |
| 已供物品： | 板，CD |
| 相关产品： | AD7920BKSZ-500RL7TR-ND - IC ADC 12BIT SRL 250KSPS SC70-6 AD7920AKSZ-REEL7-ND - IC ADC 12BIT SRL 250KSPS SC70-6 AD7920AKSZ-500RL7TR-ND - IC ADC 12BIT SRL 250KSPS SC70-6 AD7920BRMZ-REEL7-ND - IC ADC 12BIT SRL 250KSPS 8MSOP AD7920BKSZ-REEL7-ND - IC ADC 12BIT SRL 250KSPS SC70-6 AD7920BKSZ-REEL-ND - IC ADC 12BIT SRL 250KSPS SC70-6 AD7920BRMZ-REEL-ND - IC ADC 12BIT SRL 250KSPS 8MSOP AD7920BRMZ-ND - IC ADC 12BIT 250KSPS 8-MSOP |
AD7910/AD7920
Rev. C | Page 15 of 24
AD7910/
AD7920
VDD
VIN
SERIAL
INTERFACE
0V TO VDD
INPUT
μC/μP
GND
SCLK
SDATA
CS
0.1
μF
10
μF
1
μF
TANT
0.1
μF
680nF
3V
5V
SUPPLY
1.2mA
REF193
02976-017
Figure 17. REF193 as Power Supply
Table 6 provides typical performance data with various
references used as a VDD source for a 100 kHz input tone at
room temperature, under the same setup conditions.
Table 6. AD7920 Typical Performance for Various Voltage
References IC
Reference Tied to VDD
AD7920 SNR Performance (dB)
AD780 @ 3 V
72.65
72.35
AD780 @ 2.5 V
72.5
72.2
72.6
ANALOG INPUT
Figure 18 shows an equivalent circuit of the analog input
structure of the AD7910/AD7920. The two diodes, D1 and D2,
provide ESD protection for the analog input. Care must be
taken to ensure that the analog input signal never exceeds the
supply rails by more than 300 mV. This causes these diodes to
become forward biased and start conducting current into the
substrate. The maximum current these diodes can conduct
without causing irreversible damage to the parties is 10 mA.
Capacitor C1 in Figure 18 is typically about 6 pF and can be
attributed primarily to pin capacitance. Resistor R1 is a lumped
component made up of the on resistance of a switch. This
resistor is typically about 100 Ω. Capacitor C2 is the ADC
sampling capacitor and has a capacitance of 20 pF typically. For
ac applications, removing high frequency components from the
analog input signal is recommended by use of a band-pass filter
on the relevant analog input pin. In applications where
harmonic distortion and signal-to-noise ratio are critical, the
analog input should be driven from a low impedance source.
Large source impedances significantly affect the ac performance
of the ADC. This can necessitate the use of an input buffer
amplifier. The choice of the op amp is a function of the
particular application.
C1
6pF
C2
20pF
R1
D1
D2
CONVERSION PHASE—SWITCH OPEN
TRACK PHASE—SWITCH CLOSED
VDD
VIN
02976-018
Figure 18. Equivalent Analog Input Circuit
Table 7 provides some typical performance data with various op
amps used as the input buffer for a 100 kHz input tone at room
temperature, under the same setup conditions.
Table 7. AD7920 Typical Performance for Various Input
Buffers, VDD = 3 V
Op Amp in the Input Buffer
AD7920 SNR Performance (dB)
72.3
72.5
71.4
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum
source impedance depends on the amount of total harmonic
distortion (THD) that can be tolerated. The THD increases as
the source impedance increases, and performance degrades (see
DIGITAL INPUTS
The digital inputs applied to the AD7910/AD7920 are not limited
by the maximum ratings that limit the analog input. Instead, the
digital inputs applied can go to 7 V and are not restricted by the
VDD + 0.3 V limit as on the analog input. For example, if the
AD7910/AD7920 were operated with a VDD of 3 V, then 5 V logic
levels could be used on the digital inputs. However, it is important
to note that the data output on SDATA still have 3 V logic levels
when VDD = 3 V. Another advantage of SCLK and CS not being
restricted by the VDD + 0.3 V limit is that power supply
sequencing issues are avoided. If CS or SCLK is applied before
VDD, there is no risk of latch-up as there would be on the analog
inputs if a signal greater than 0.3 V were applied prior to VDD.
相关PDF资料 |
PDF描述 |
|---|---|
| EVAL-AD7910CBZ | BOARD EVALUATION FOR AD7910 |
| VI-B32-EY | CONVERTER MOD DC/DC 15V 50W |
| SDR0503-150ML | INDUCTOR POWER 15UH 20% SMD |
| VI-B31-EY | CONVERTER MOD DC/DC 12V 50W |
| MLK1005S4N3S | INDUCTOR MULTILAYER 4.3NH 0402 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7922CB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD7922CBZ | 功能描述:BOARD EVAL FOR AD7922 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7923CB2 | 制造商:AD 制造商全称:Analog Devices 功能描述:4-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 16-Lead TSSOP |
| EVAL-AD7923CBZ | 功能描述:BOARD EVAL FOR AD7923 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7927CB | 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD. - Bulk |
发布紧急采购，3分钟左右您将得到回复。