- 您现在的位置：买卖IC网 > PDF目录16587 > EVAL-ADCMP607BCPZ (Analog Devices Inc)BOARD EVAL FOR ADCMP607 12LFCSP PDF资料下载
参数资料
| 型号： | EVAL-ADCMP607BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADCMP607 12LFCSP |
| 标准包装： | 1 |
| 主要目的： | 比较器，单路 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADCMP607 |
| 主要属性： | CML 兼容输出 |
| 次要属性： | 锁销启用和关机引脚 |
| 已供物品： | 板 |
ADCMP606/ADCMP607
Rev. A | Page 11 of 16
COMPARATOR PROPAGATION DELAY
DISPERSION
The ADCMP606/ADCMP607 comparators are designed to
reduce propagation delay dispersion over a wide input overdrive
range of 5 mV to VCCI 1 V. Propagation delay dispersion is the
variation in propagation delay that results from a change in the
degree of overdrive or slew rate (that is, how far or how fast the
input signal exceeds the switching threshold).
Propagation delay dispersion is a specification that becomes
important in high speed, time-critical applications, such as data
communication, automatic test and measurement, and instru-
mentation. It is also important in event-driven applications, such
as pulse spectroscopy, nuclear instrumentation, and medical
imaging. Dispersion is defined as the variation in propagation
delay as the input overdrive conditions are changed (Figure 15
and Figure 16).
The device dispersion is typically 2.3 ns as the overdrive varies
from 10 mV to 125 mV. This specification applies to both
positive and negative signals because each device has very closely
matched delays for positive-going and negative-going inputs as
well as very low output skews.
Q/Q OUTPUT
INPUT VOLTAGE
500mV OVERDRIVE
10mV OVERDRIVE
DISPERSION
VN ± VOS
05
91
7-
0
14
Figure 15. Propagation Delay—Overdrive Dispersion
Q/Q OUTPUT
INPUT VOLTAGE
10V/ns
1V/ns
DISPERSION
VN ± VOS
05
91
7-
0
15
Figure 16. Propagation Delay—Slew Rate Dispersion
COMPARATOR HYSTERESIS
The addition of hysteresis to a comparator is often desirable in
a noisy environment, or when the differential input amplitudes
are relatively small or slow moving. Figure 17 shows the transfer
function for a comparator with hysteresis. As the input voltage
approaches the threshold (0 V, in this example) from below the
threshold region in a positive direction, the comparator switches
from low to high when the input crosses +VH/2, and the new
switching threshold becomes VH/2. The comparator remains in
the high state until the new threshold, VH/2, is crossed from
below the threshold region in a negative direction. In this manner,
noise or feedback output signals centered on 0 V input cannot
cause the comparator to switch states unless it exceeds the region
bounded by ±VH/2.
OUTPUT
INPUT
0
VOL
VOH
+VH
2
–VH
2
05
91
7-
0
16
Figure 17. Comparator Hysteresis Transfer Function
The customary technique for introducing hysteresis into a
comparator uses positive feedback from the output back to
the input. One limitation of this approach is that the amount
of hysteresis varies with the output logic levels, resulting in
hysteresis that is not symmetric about the threshold. The
external feedback network can also introduce significant
parasitics that reduce high speed performance and induce
oscillation in some cases.
This ADCMP607 comparator offers a programmable hysteresis
feature that can significantly improve accuracy and stability.
Connecting an external pull-down resistor or a current source
from the LE/HYS pin to GND, varies the amount of hysteresis
in a predictable, stable manner. Leaving the LE/HYS pin discon-
nected or driving this pin high removes hysteresis. The maximum
hysteresis that can be applied using this pin is approximately
160 mV. Figure 18 illustrates typical hysteresis applied as a
function of the external resistor value, and Figure 7 illustrates
typical hysteresis as a function of the current.
H
Y
ST
ER
ES
IS
(
m
V)
HYS RESISTOR (k)
0
50
100
150
200
250
300
350
400
50 100 150 200 250 300 350 400 450 500 550 600 650
VCC = 2.5V
05
91
7-
01
7
Figure 18. Hysteresis vs. RHYS Control Resistor
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33099CEGR2 | IC VREG ALTERNATOR ADAPT 16-SOIC |
| V300B24E150BL3 | CONVERTER MOD DC/DC 24V 150W |
| EVAL-ADCMP602BRMZ | BOARD EVAL FOR ADCMP602 8MSOP |
| MCZ33099CEG | IC VREG ALTERNATOR ADAPT 16-SOIC |
| V300B24E150BG | CONVERTER MOD DC/DC 24V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADCMP608BKSZ | 功能描述:BOARD EVAL FOR ADCMP608 SC70-6 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-ADCMP609BRMZ | 功能描述:BOARD EVAL FOR ADCMP609 8MSOP RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-ADDIFFAMP-1R | 制造商:Analog Devices 功能描述:EVALUATION BOARD AD7751 - Bulk |
| EVAL-ADDIFFAMP-1RZ | 制造商:Analog Devices 功能描述:EVAL BD DIFFERENTIAL DRVR EVAL BD - Bulk |
| EVAL-ADE5169EBZ-2 | 功能描述:BOARD EVALUATION FOR AD5169 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
发布紧急采购，3分钟左右您将得到回复。