- 您现在的位置：买卖IC网 > PDF目录1790 > FAN2106EMPX (Fairchild Semiconductor)IC REG BUCK SYNC ADJ 6A 25MLP PDF资料下载
参数资料
| 型号： | FAN2106EMPX |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 12/15页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 6A 25MLP |
| 标准包装： | 1 |
| 系列： | TinyBuck™ |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 3 V ~ 21 V |
| 输入电压： | 3 V ~ 24 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 300kHz ~ 600kHz |
| 电流 - 输出： | 6A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 25-MLP |
| 包装： | 标准包装 |
| 供应商设备封装： | 25-MLP（5x6） |
| 产品目录页面： | 1220 (CN2011-ZH PDF) |
| 配用： | FEB167-ND - BOARD EVAL FOR FAN2106 |
| 其它名称： | FAN2106EMPXDKR |
Setting the Ramp Resistor Value
R RAMP resistor plays a critical role in the design by
providing charging current to the internal ramp capacitor
Since the I LIM voltage is set by a 10 μA current source
into the R ILIM resistor, the basic equation for setting the
reference voltage is:
and also serving as a means to provide input voltage
feedforward.
R RAMP is calculated by the following formula:
V RILIM = 10μA*R ILIM
To calculate R ILIM :
(7)
R RAMP ( K Ω ) =
( V IN ? 1 . 8 ) ? V OUT
( 18 ) ? V IN ? f ? 10 ? 6
? 2
where frequency (f) is expressed in KHz.
(5)
R ILIM = V RILIM / 10μA (8)
The voltage V RILIM is made up of two components, V BOT
(which relates to the current through the low-side
MOSFET) and V RMPEAK (which relates to the peak
For wide input operation, first calculate R RAMP for the
minimum and maximum input voltage conditions and
current through the inductor). Combining those two
voltage terms results in:
use larger of the two values calculated.
In all applications, current through the R RAMP pin must
be greater than 10 μA from the equation below for
proper operation:
R ILIM = (V BOT + V RMPEAK )/ 10μA
R ILIM = {0.96 + (I LOAD * R DSON *K T *8)} +
{D*(V IN – 1.8)/(f SW *0.03*R RAMP )}/10μA
(9)
(10)
V IN ? 1 . 8
R RAMP + 2
≥ 10 μ A
(6)
where:
V BOT = 0.96 + (I LOAD * R DSON *K T *8);
If the calculated R RAMP values in Equation (5) result in a
current less than 10 μA, use the R RAMP value that
satisfies Equation (6). In applications with large input
ripple voltage, the R RAMP resistor should be adequately
decoupled from the input voltage to minimize ripple on
the RAMP pin .
Setting the Current Limit
The current limit system involves two comparators. The
MAX I LIMIT comparator is used with a V ILIM fixed-voltage
reference and represents the maximum current limit
allowable. This reference voltage is temperature
compensated to reflect the R DSON variation of the low-
side MOSFET. The ADJUST I LIMIT comparator is used
where the current limit needs to be set lower than the
V ILIM fixed reference. The 10 μA current source does not
track the R DSON changes over temperature, so change is
added into the equations for calculating the ADJUST
I LIMIT comparator reference voltage, as is shown below.
Figure 24 shows a simplified schematic of the over-
current system.
V RMPEAK = D*(V IN – 1.8)/(f SW *0.03*R RAMP );
I LOAD = the desired maximum load current;
R DSON = the nominal R DSON of the low-side MOSFET;
K T = the normalized temperature coefficient for the
low-side MOSFET (on datasheet graph);
D = V OUT /V IN duty cycle;
f SW = Clock frequency in kHz; and
R RAMP = chosen ramp resistor value in k Ω .
After 16 consecutive, pulse-by-pulse, current-limit
cycles, the fault latch is set and the regulator shuts
down. Cycling V CC or EN restores operation after a
normal soft-start cycle (refer to the Auto-Restart
section) .
The over-current protection fault latch is active during
the soft-start cycle. Use 1% resistor for R ILIM .
RAMP
VERR
+
_
+
PWM
COMP
MAX
ILIMIT
PWM
10μA
V CC
VILIM
_
ILIM
+
_
ADJUST
ILIMIT
ILIMTRIP
RILIM
Figure 24. Current-Limit System Schematic
? 2009 Fairchild Semiconductor Corporation
FAN2106 ? Rev. 1.1.2
12
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FAN2108EMPX | IC REG BUCK SYNC ADJ 8A 25MLP |
| FAN2110EMPX | IC REG BUCK SYNC ADJ 10A 25MLP |
| FAN21SV04MPX | IC REG BUCK SYNC ADJ 4A 25MLP |
| FAN21SV06MPX | IC REG BUCK SYNC ADJ 6A 25MLP |
| FAN2500S30X | IC REG LDO 3V .1A SOT-23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN2106EMPX_12 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:TinyBucka?￠ 3-24 V Input, 6 A, High-Efficiency, Integrated Synchronous Buck Regulator |
| FAN2106MPX | 功能描述:直流/直流开关转换器 6A 24V Input Intgr Syn Buck Regulator RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| FAN2106MPX_12 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:TinyBucka?￠ 3-24 V Input, 6 A, High-Efficiency, Integrated Synchronous Buck Regulator |
| FAN2106MPX-CUT TAPE | 制造商:FAIRCHILD 功能描述:FAN2106 Series 3 to 24 V 6 A 600 kHz Synchronous Buck Regulator - MLP-25 |
| FAN2107_ABC3086B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。