FAN4800AU/CU " Rev. 1.0.1
?/DIV>
7.94
Figure 29. Modulation Gain Characteristics
V
IN
I
L
V
E A
Figure 30. Line Feed-Forward Operation
To sense the RMS value of the line voltage, averaging
circuit with two poles is typically employed, as shown in
Figure 28. Notice that the input voltage of the PFC is
clamped at the peak of the line voltage once the PFC
stops switching because the junction capacitance of the
bridge diode is not discharged, as shown in Figure 31.
Therefore, the voltage divider for VRMS should be
designed considering the brownout protection trip-point
and minimum operation line voltage.
PFC Runs
PFC Stops
V
IN
V
RMS
Figure 31. V
RMS
According to the PFC Operation
The rectified sinusoidal signal is obtained by the current
flowing into the IAC pin. The resistor R
IAC
should be
large   enough   to   prevent   saturation   of   the   gain
modulator, calculating as:
A
G
R
V
M A X
IA
M IN
LINE
m
140
2
<
?/DIV>
(3)
where V
LINEMIN
is the line voltage that trips brownout
protection, G
MAX
is the maximum modulator gain
when V
RMS
is 1.08 V (which can be found in the
datasheet), and 140 礎 is the maximum output
current of the gain modulator.
Current Control of Boost Stage
The FAN4800AU/CU employs two control loops for
power factor correction, as shown in Figure 32: a
current-control loop and a voltage-control loop. The
current-control loop shapes inductor current as shown
in Figure 33 based on the reference signal obtained at
the IAC pin calculated as:
M
A
M
M
L
R
G
I
R
I
R
?/DIV>
?/DIV>
=
?/DIV>
=
?/DIV>
1
(4)
IS E N S E
IA C
V R M S
V E A
IE A
R
M
R  M
R
R M  S 1
R
R M  S 2
R  R M  S 3
C
R M  S 1
C  R M  S 2
R  I A C
I
A C
V
I N
I
L
R
C S 1
R
F 1
C
F 1
I M  O
R
I C
C  I C 1
C
I C 2
+
-
D riv e
lo g ic
O P F C
2 .5 V
R
V C
R
V C 1
R
V C 2
F B P F C
R
F B 1
R
F B 2
V
O
V R E F
Figure 32. Gain Modulation Block
I
A C
I
L
M
M
O
R
R
Figure 33. Inductor Current Shaping
The current-control feedback loop also has a pulse-by-
pulse current limit comparator that forces the PFC
switch to turn off until the next switching cycle if the
ISENSE pin voltage drops below -1.3 V.
相关代理商/技术参数 |
参数描述 |
| FAN4800C |
制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:PFC/PWM Controller Combination |
| FAN4800CMY |
功能描述:电流型 PWM 控制器 PWM/PFC, Avg Curr 30uA SU, 2.6mA Op RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| FAN4800CNY |
功能描述:电流型 PWM 控制器 PWM/PFC, Avg Curr 30uA SU, 2.6mA Op RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| FAN4800CS |
制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:PFC/PWM Controller Combination |
| FAN4800CSMY |
功能描述:电流型 PWM 控制器 PFC/PWM Controller Combination RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |