- 您现在的位置：买卖IC网 > PDF目录299042 > FAN5093MTC PDF资料下载
参数资料
| 型号： | FAN5093MTC |
| 文件页数： | 8/21页 |
| 文件大小： | 500K |
| 代理商： | FAN5093MTC |
FAN5093
PRODUCT SPECIFICATION
16
REV. 1.0.8 2/4/02
BYPASS Reference
The internal logic of the FAN5093 runs on 5V. To permit the
IC to run with 12V only, it produces 5V internally with a
linear regulator, whose output is present on the BYPASS pin.
This pin should be bypassed with a 1F capacitor for noise
suppression. The BYPASS pin should not have any external
load attached to it.
Dynamic Voltage Adjustment
The FAN5093 has internal pullups on its VID lines. External
pullups should not be used. The FAN5093 can have its output
voltage dynamically adjusted to accommodate low power
modes. The designer must ensure that the transitions on the
VID lines all occur simultaneously (within less than
500nsec)
to avoid false codes generating undesired output voltages.
The Power Good ag tracks the VID codes, but has a
500sec delay transitioning from high to low; this is long
enough to ensure that there will not be any glitches during
dynamic voltage adjustment.
Power Good (PWRGD)
The FAN5093 Power Good function is designed in accor-
dance with the Pentium IV DC-DC converter specications
and provides a continuous voltage monitor on the VFB pin.
The circuit compares the VFB signal to the VREF voltage
and outputs an active-low interrupt signal to the CPU should
the power supply voltage deviate more than +14%/-9% of its
nominal setpoint. The output is guaranteed open-collector
high when the power supply voltage is within +6%/-11% of
its nominal setpoint. The Power Good ag provides no
control functions to the FAN5093.
Output Enable/Soft Start (ENABLE/SS)
The FAN5093 will accept an open collector/TTL signal for
controlling the output voltage. The low state disables the
output voltage. When disabled, the PWRGD output is in the
low state.
Even if an enable is not required in the circuit, this pin
should have attached a capacitor (typically 100nF) to soft-
start the switching. A softstart capacitor may be approxi-
mately chosen by the formula:
However, C must be
≥ 10nF.
Oscillator
The FAN5093 oscillator section runs at a frequency deter-
mined by a resistor from the RT pin to ground according to
the formula
The oscillator generates two internal sawtooth ramps, each at
one-half the oscillator frequency, and running 180
° out of
phase with each other. These ramps cause the turn-on time of
the two phases to be phased apart. The oscillator frequency
of the FAN5093 can be programmed from 200KHz to 2MHz
with each phase running at 100KHz to 1MHz, respectively.
Selection of a frequency will depend on various system
performance criteria, with higher frequency resulting in
smaller components but lower efciency.
Programmable Active Droop
The FAN5093 features Programmable Active Droop: as
the output current increases, the output voltage drops propor-
tionately an amount that can be programmed with an exter-
nal resistor. This feature is offered in order to allow
maximum headroom for transient response of the converter.
The current is sensed losslessly by measuring the voltage
across the low-side MOSFET during its on time. Consult the
section on current sensing for details. Note that this method
makes the droop dependent on the temperature and initial
tolerance of the MOSFET, and the droop must be calculated
taking account of these tolerances. Given a maximum output
current, the amount of droop can be programmed with a
resistor to ground on the droop pin, according to the formula
with VDroop the desired droop voltage, RT the oscillator
resistor, Imax the output current at which the droop is desired,
and RDS, on the on-state resistance of one phase’s low-side
MOSFET.
Typical response time of the FAN5093 to an output voltage
change is 100nsec.
Important Note! The oscillator frequency must be selected
before selecting the droop resistor, because the value of RT
is used in the calculation of RDroop.
Higher Current Converters
Active droop makes it possible to parallel multiple
FAN5093s for even higher output current requirements.
Synchronized parallelization may be obtained with the
similar FAN5094. Please refer to Application Bulletin
AB-XX for details.
Over-Voltage Protection
The FAN5093 constantly monitors the output voltage for
protection against over-voltage conditions. If the voltage at
the VFB pin exceeds 2.2V, an over-voltage condition is
assumed and the FAN5093 latches on the external low-side
MOSFET and latches off the high-side MOSFET. The
DC-DC converter returns to normal operation only after VCC
has been recycled.
C
t10
A
1V
out
+
----------------------
=
RT
()
25
10
9
fHz
()
----------------------
=
R
Droop
()
V
Droop
RT
I
max
R
DS on
,
-------------------------------------
=
相关PDF资料 |
PDF描述 |
|---|---|
| FAP-02 | 10 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER, PLUG |
| FB-3225 | Boom microphone |
| FB-3524 | Boom microphone |
| FB-3525 | Boom microphone |
| FB-3529 | Boom microphone |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN5093MTC_Q | 功能描述:DC/DC 开关控制器 Sync Buck Converter 2Phs Interleaved RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| FAN5093MTCX | 功能描述:DC/DC 开关控制器 Sync Buck Converter 2Phs Interleaved RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| FAN5094 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Multi-Phase Interleaved Buck Converter |
| FAN5094MTC | 功能描述:直流/直流开关转换器 Buck Converter Hi Cur Sys Voltage RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| FAN5094MTC_Q | 功能描述:DC/DC 开关控制器 Buck Converter Hi Cur Sys Voltage RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。