- 您现在的位置：买卖IC网 > PDF目录21970 > FAN7532MX (Fairchild Semiconductor)IC CONTROLLER BALLAST 16-SOIC PDF资料下载
参数资料
| 型号： | FAN7532MX |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER BALLAST 16-SOIC |
| 标准包装： | 1 |
| 类型： | 镇流器控制器 |
| 频率： | 48 ~ 52 kHz |
| 电流 - 电源： | 6.4mA |
| 电流 - 输出： | 500mA |
| 电源电压： | 11 V ~ 15.6 V |
| 工作温度： | -25°C ~ 125°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 标准包装 |
| 产品目录页面： | 1216 (CN2011-ZH PDF) |
| 其它名称： | FAN7532MXDKR |
( 5 V ? 2.9 V ) = I PH
I CT RT +
I PH ? I RT
( 5 V ? 2.9 V )
( 5 V ? V CPH )
I CT = I RT +
( 5 V ? V CPH )
I PH ? I RT
( 5 V ? 2.9 V )
t pre = CPH ×
V CPH
I pre _ ch = 4 ×
V ref
( 6.25 × V ref )
t pre _ ch = C T ×
dV CT
I pre _ ch
t pre _ disch = C T ×
dV CT
I run _ ch = 2 ×
V ref
R T
( 6.25 × V ref )
I run _ disch = 2 × , Vref=4V (Constant)
t run _ ch = C T ×
dV CT
t run _ disch = C T ×
dV CT
0 V ≤ V CPH ≤ 2.9 V , ;Preheating Frequency
= I
2.9 V ≤ V CPH ≤ 5 V , ;Ignition Frequency
I PH ? I RT
( 5 V ? 2.9 V )
V CPH ≥ 5 V
I CT = I RT , ;Run Frequency
4. Preheating Mode
The preheating mode is defined as the IC’s internal
status when the V CPH is between 0V and 2.9V. During
preheating, the current that flows through the ballast
circuit heats the lamp filaments. This is necessary for
maximizing lamp life and reducing the required ignition
voltage. When the V CC exceeds the UVLO high
threshold, the preheating time set-up capacitor, CPH,
starts being charged by the internal 1.5μA current source
until the V CPH reaches 2.9V. Until the VCPH reaches
2.9V, the switching frequency throughout the preheating
mode is determined by CT and RPH.
The preheating time is determined by the CPH and the
1.5μA current source. Therefore, the preheating time is
determined by equation (3):
(3)
I charging
The preheating frequency is determined by the amount
of charging and discharging current to the CT capacitor.
The charging and discharging current during preheating
mode is decided by equation (4):
(4)
R PH
I pre _ disch = 4 × , Vref = 4 V ( Constant )
R PH
The charging and discharging time of the CT capacitor
during preheating mode is decided by equation (5):
(5)
, dVCT=3.45V (Constant)
I pre _ disch
Finally, the FAN7532’s preheating frequency in the
preheating period is determined by equation (6):
5. Ignition Mode
The ignition mode is defined as the IC’s internal status
when V CPH is approximately between 2.9V and 5V.
During ignition, the operating frequency is decreased to
a pre-determined value. At the same time, a very high-
voltage for igniting the lamp is established across the
lamp. When the V CPH exceeds 2.9V, the FAN7532
enters the ignition mode. Once V CPH exceeds 5V, the
device enters the run mode described in the following
section. In the ignition period, the internal 10mA current
source charges the external preheating timing capacitor
(CPH) to increase noise immunity with the sharp slope of
the V CPH . The ignition time is determined by the CPH
and internal 10mA current source ( Δ T ign = C PH × Δ I V CPH CPH ). In this
mode, the switching frequency is determined by CT,
RPH, and RT. Therefore, the charging and discharging
currents change according to V CPH and are determined
by equation (7).
I CT = I RT + (7)
6. Run Mode
After the lamp has successfully ignited, the FAN7532
enters run mode. The run mode is defined as the IC’s
internal status when V CPH is higher than 5V. In this
mode, the lamp is being driven with a normal power level
after the lamp is discharged. The run mode switching
frequency is determined by the timing resistor RT and
the timing capacitor CT. When the V CPH exceeds 5V, the
protection-masking mode is disabled and the IC can
enter the protection mode. The running frequency is
determined by the amount of charging and discharging
current to CT capacitor.
The charging and discharging currents during preheating
mode are decided by the equation (8):
(8)
R T
(9)
I run _ ch
, dVCT=3.45V (Constant)
I run _ disch
Finally, the preheating frequency in the preheating period
f run =
(
)
2 × t run _ ch + t run _ disch
f pre =
2 × ( t pre _ ch + t pre _ disch
1
)
(6)
using the FAN7532 is determined by the equation (10):
1
(10)
? 2006 Fairchild Semiconductor Corporation
FAN7532 Rev. 1.0.2
10
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| M24308/23-1 | CONN D-SUB RCPT 9POS VERT PCB |
| 5-1624113-9 | INDUCTOR .39UH 5% 0805 |
| 5-1624113-5 | INDUCTOR .27UH 5% 0805 |
| IR21592PBF | IC CTLR BALLAST DIMMING 16-DIP |
| 5-1624113-1 | INDUCTOR .20UH 5% 0805 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN7535 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:PFC & Ballast Control IC |
| FAN7535M | 功能描述:功率因数校正 IC Half-bridge Gate RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| FAN7535MX | 功能描述:开关变换器、稳压器与控制器 Electronic Ballast PFC Combo IC RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| FAN7544 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Simple Ballast Controller |
| FAN7544M | 功能描述:开关变换器、稳压器与控制器 Electronic Ballast Controller RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。