- 您现在的位置：买卖IC网 > PDF目录21970 > FAN7532MX (Fairchild Semiconductor)IC CONTROLLER BALLAST 16-SOIC PDF资料下载
参数资料
| 型号： | FAN7532MX |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 12/16页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER BALLAST 16-SOIC |
| 标准包装： | 1 |
| 类型： | 镇流器控制器 |
| 频率： | 48 ~ 52 kHz |
| 电流 - 电源： | 6.4mA |
| 电流 - 输出： | 500mA |
| 电源电压： | 11 V ~ 15.6 V |
| 工作温度： | -25°C ~ 125°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 标准包装 |
| 产品目录页面： | 1216 (CN2011-ZH PDF) |
| 其它名称： | FAN7532MXDKR |
2) Open Lamp Protection (OLP) Mode
After the lamp has successfully ignited, the FAN7532
enters run mode. In this mode, if one of the cathodes
isn’t correctly connected to the ballast, the ballast stops
operation for safety until the lamp is changed and a new
one is connected between the lamp and the ballast. As
soon as the voltage of OLP pin exceeds 2V, the IC
15.6V
V UVLO+
V UVLO-
V CPH
enters the protection mode. However, the FAN7532 out-
puts are only disabled in this mode. To exit protection
mode, the lamp must be replaced or correctly connected
to the ballast.
5V
2.9V
FREQ
f PH
f OSC
OLP
V LAMP
Reset when open lamp
Open lamp
Only gate driver
is disabled
Reset when open lamp
Open lamp
Only gate driver
is disabled
Run
Open
Lamp
Preheating
Ignition
Run
Open
Lamp
Preheating
Ignition
Run
FAN7532 Rev. 00
Figure 19. Timing Diagram (OLP Mode)
8. PCB Layout Guides
Component selection and placement on the PCB is very
important when using power control ICs. Bypass the V CC
to GND as close to the IC terminals as possible with a
low ESR/ESL capacitor, as shown in Figure 20. This
bypassed capacitor can reduce the noise from the power
supply parts, such as a startup resistor and a charge
pump. The GND lead should be directly connected to the
low-side power MOSFET using an individual PCB trace.
In addition, the ground return path of the timing compo-
nents (CPH, CT, RPH, RT) and V CC decoupling capaci-
tor should be connected directly to the IC GND lead and
not via separate traces or jumpers to other ground traces
on the board. These connection techniques prevent
high-current ground loops from interfering with sensitive
timing component operations and allow the entire control
? 2006 Fairchild Semiconductor Corporation
FAN7532 Rev. 1.0.2
12
circuit to reduce common-mode noise due to output
switching.
Figure 20. PCB Layout
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| M24308/23-1 | CONN D-SUB RCPT 9POS VERT PCB |
| 5-1624113-9 | INDUCTOR .39UH 5% 0805 |
| 5-1624113-5 | INDUCTOR .27UH 5% 0805 |
| IR21592PBF | IC CTLR BALLAST DIMMING 16-DIP |
| 5-1624113-1 | INDUCTOR .20UH 5% 0805 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN7535 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:PFC & Ballast Control IC |
| FAN7535M | 功能描述:功率因数校正 IC Half-bridge Gate RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| FAN7535MX | 功能描述:开关变换器、稳压器与控制器 Electronic Ballast PFC Combo IC RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| FAN7544 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Simple Ballast Controller |
| FAN7544M | 功能描述:开关变换器、稳压器与控制器 Electronic Ballast Controller RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。