- 您现在的位置：买卖IC网 > PDF目录67429 > FC250H1 (LINEAGE POWER LLC) DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | FC250H1 |
| 厂商： | LINEAGE POWER LLC |
| 元件分类： | 电源模块 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 封装： | MODULE-20 |
| 文件页数： | 3/20页 |
| 文件大小： | 564K |
| 代理商： | FC250H1 |
Lineage Power
11
Data Sheet
April 2008
18 Vdc to 36 Vdc Input, 24 Vdc Output; 250 W
FC250H1 Power Module: dc-dc Converter;
Feature Descriptions (continued)
Output Overvoltage Protection
The output voltage is monitored at the VO(+) and VO(–)
pins of the module. If the voltage at these pins exceeds
the value indicated in the feature specications table,
the module will shut down and latch off. Recovery from
latched shutdown is accomplished by cycling the dc
input power off for at least 1.0 second or toggling the
primary referenced on/off signal for at least 1.0 second.
Output Current Monitor
The CURRENT MON pin provides a dc voltage propor-
tional to the dc output current of the module given in
the Feature Specications table. For example, on the
FC250H1, the V/A ratio is set at 370 mV/A
± 10% @
70
°C case. At a full load current of 10.4 A, the voltage
on the CURRENT MON pin is 3.848 V. The current
monitor signal is referenced to the SENSE(–) pin on
the secondary and is supplied from a source imped-
ance of approximately 2 k
. It is recommended that the
CURRENT MON pin be left open when not in use,
although no damage will result if the CURRENT MON
pin is shorted to secondary ground. Directly driving the
CURRENT MON pin with an external source will detri-
mentally affect operation of the module and should be
avoided.
Synchronization
Any module can be synchronized to any other module
or to an external clock using the SYNC IN or SYNC
OUT pins. The modules are not designed to operate in
a master/slave conguration; that is, if one module fails,
the other modules will continue to operate.
SYNC IN Pin
This pin can be connected either to an external clock or
directly to the SYNC OUT pin of another FC250x mod-
ule.
If an external clock signal is applied to the SYNC IN
pin, the signal must be a 500 kHz (±50 kHz) square
wave with a 4 Vp-p amplitude. Operation outside this
frequency band will detrimentally affect the perfor-
mance of the module and must be avoided.
If the SYNC IN pin is connected to the SYNC OUT pin
of another module, the connection should be as direct
as possible, and the VI(–) pins of the modules must be
shorted together.
Unused SYNC IN pins should be tied to VI(–). If the
SYNC IN pin is unused, the module will operate from
its own internal clock.
SYNC OUT Pin
This pin contains a clock signal referenced to the VI(–)
pin. The frequency of this signal will equal either the mod-
ule’s internal clock frequency or the frequency estab-
lished by an external clock applied to the SYNC IN pin.
When synchronizing several modules together, the
modules can be connected in a daisy-chain fashion
where the SYNC OUT pin of one module is connected
to the SYNC IN pin of another module. Each module in
the chain will synchronize to the frequency of the rst
module in the chain.
To avoid loading effects, ensure that the SYNC OUT
pin of any one module is connected to the SYNC IN pin
of only one module. Any number of modules can be
synchronized in this daisy-chain fashion.
Overtemperature Protection
To provide protection in a fault condition, the unit is
equipped with an overtemperature shutdown circuit.
The shut down circuit will not engage unless the unit is
operated above the maximum case temperature.
Recovery from overtemperature shutdown is
accomplished by cycling the dc input power off for at
least 1.0 second or toggling the primary referenced on/
off signal for at least 1.0 second.
Forced Load Sharing (Parallel Operation)
For either redundant operation or additional power
requirements, the power modules can be congured for
parallel operation with forced load sharing (see
Figure 17). For a typical redundant conguration,
Schottky diodes or an equivalent should be used to
protect against short-circuit conditions. Because of the
remote sense, the forward-voltage drops across the
Schottky diodes do not affect the set point of the
voltage applied to the load. For additional power
requirements, where multiple units are used to develop
combined power in excess of the rated maximum, the
Schottky diodes are not needed.
相关PDF资料 |
PDF描述 |
|---|---|
| FC250H1 | 1-OUTPUT 250 W DC-DC REG PWR SUPPLY MODULE |
| FC250H1 | 1-OUTPUT 250 W DC-DC REG PWR SUPPLY MODULE |
| FC30 | SPECIALTY ANALOG CIRCUIT, PBGA14 |
| FC30TR | SPECIALTY ANALOG CIRCUIT, PBGA14 |
| FCD4A14CCB | IMAGE SENSOR, UUC19 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FC250R | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Power Module:dc-dc Converter; 18 Vdc to 36 Vdc Input, 28 Vdc Output; 250 W |
| FC250R1 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Power Module:dc-dc Converter; 18 Vdc to 36 Vdc Input, 28 Vdc Output; 250 W |
| FC2528 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| FC252U | 制造商:AB 功能描述:POT2.5K ALLEN BRADLEY S7D7B |
| FC255 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:THIN SMD LOW / MEDIUM FREQUENCY CRYSTAL UNIT |
发布紧急采购，3分钟左右您将得到回复。