- 您现在的位置：买卖IC网 > PDF目录20492 > FLASHPRO4 (Microsemi SoC)PROGRAMMER FLASH FPGA PDF资料下载
参数资料
| 型号： | FLASHPRO4 |
| 厂商： | Microsemi SoC |
| 文件页数： | 1/14页 |
| 文件大小： | 0K |
| 描述： | PROGRAMMER FLASH FPGA |
| 标准包装： | 1 |
| 类型： | 闪存 |
| 适用于相关产品： | IGlOO?，ProASIC?3，SmartFusion? 保险丝，ProASIC（plus） |
| 所含物品： | 编程器 |
| 其它名称： | 1100-1140 |
Programming Flash Devices
Introduction
This document provides an overview of the various programming options available for the Microsemi
flash families. The electronic version of this document includes active links to all programming resources,
which are available at http://www.microsemi.com/soc/products/hardware/default.aspx . For Microsemi
antifuse devices, refer to the Programming Antifuse Devices document.
Summary of Programming Support
FlashPro4 and FlashPro3 are high-performance in-system programming (ISP) tools targeted at the latest
generation of low power flash devices offered by the SmartFusion, ? Fusion, IGLOO, ? and ProASIC ? 3
families, including ARM-enabled devices. FlashPro4 and FlashPro3 offer extremely high performance
through the use of USB 2.0, are high-speed compliant for full use of the 480 Mbps bandwidth, and can
program ProASIC3 devices in under 30 seconds. Powered exclusively via USB, FlashPro4 and
FlashPro3 provide a VPUMP voltage of 3.3 V for programming these devices.
FlashPro4 replaced FlashPro3 in 2010. FlashPro4 supports SmartFusion, Fusion, ProASIC3,and IGLOO
devices as well as future generation flash devices. FlashPro4 also adds 1.2 V programming for IGLOO
nano V2 devices. FlashPro4 is compatible with FlashPro3; however it adds a programming mode
(PROG_MODE) signal to the previously unused pin 4 of the JTAG connector. The PROG_MODE goes
high during programming and can be used to turn on a 1.5 V external supply for those devices that
require 1.5 V for programming. If both FlashPro3 and FlashPro4 programmers are used for programming
the same boards, pin 4 of the JTAG connector must not be connected to anything on the board because
FlashPro4 uses pin 4 for PROG_MODE.
FlashPro
Software
FlashPro3 or
FlashPro4
JTAG
ProASIC3/E
Programming File:
PDB, STP, or FDB
Figure 1 ? FlashPro Programming Setup
J ul y 2 01 0
1
相关PDF资料 |
PDF描述 |
|---|---|
| IXDN430MYI | IC MOSFET/IGBT DRIVER TO-263 |
| RBB06DHRD | CONN CARD EXTEND 12POS .050" |
| VE-2N2-CX-S | CONVERTER MOD DC/DC 15V 75W |
| RKZ-0505D/H | CONV DC/DC 2W 05VIN +/-05VOUT |
| VE-2NJ-CX-S | CONVERTER MOD DC/DC 36V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FLASHPRO5 | 功能描述:Fusion, IGLOO, IGLOO2, ProASIC3, RT ProASIC3, SmartFusion, SmartFusion2 - Programming 制造商:microsemi corporation 系列:- 零件状态:有效 类型:编程 配套使用产品/相关产品:Fusion，IGLOO，IGLOO2，ProASIC3，RT ProASIC3，SmartFusion，SmartFusion2 内容:编程器，线缆 标准包装:1 |
| FLASHPRO-CC_STD | 制造商:Elprotronic Inc 功能描述:USB Gang Flash Programmer for the CCx series Chipcon products from Texas Instruments |
| FlashPro-CC-LITE | 功能描述:程序设计器 - 基于处理器 FlashPro-CC LITE VERSION RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| FlashPro-CC-STD | 功能描述:程序设计器 - 基于处理器 FlashPro-CC STD. FOR TI CHIPCON MCU RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| FLASHPRO-CM-STD | 制造商:Elprotronic Inc 功能描述:Programmers - Processor Based FlashPro-CM STD Ver Stellaris Tiva STM |
发布紧急采购，3分钟左右您将得到回复。