- 您现在的位置：买卖IC网 > PDF目录16978 > FPF2200 (Fairchild Semiconductor)IC LOAD SWITCH 500MA 6-MICROFET PDF资料下载
参数资料
| 型号： | FPF2200 |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 9/13页 |
| 文件大小： | 0K |
| 描述： | IC LOAD SWITCH 500MA 6-MICROFET |
| 标准包装： | 1 |
| 类型： | 高端开关 |
| 输出数： | 1 |
| Rds（开）： | 185 毫欧 |
| 内部开关： | 是 |
| 电流限制： | 500mA |
| 输入电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-MLP |
| 供应商设备封装： | 6-MicroFET（2x2） |
| 包装： | 标准包装 |
| 其它名称： | FPF2200DKR |
Description of Operation
The FPF2200, FPF2201, and FPF2202 are state of the art High
Precision Current Limit switches designed to meet USB OTG
(On-The-Go) applications with optimum current for a safe
design practice. The core of each device is a 0.16 P-channel
MOSFET and a controller capable of functioning over an input
operating range of 1.8- 5.5V. The controller protects or offers
current limiting, UVLO(undervoltage lockout) and thermal
Undervoltage Lockout (UVLO)
The undervoltage lockout turns-off the switch if the input voltage
drops below the undervoltage lockout threshold. With the ON
pin active the input voltage rising above the undervoltage
lockout threshold will cause a controlled turn-on of the switch
which limits current over-shoots.
shutdown protection. The minimum current limit value is set to
500mA allowing to draw as much as 500mA from the USB port.
Output Discharge Resistor
The FPF2200/1/2 family contains an 80
on-chip load resistor
On/Off Control
The ON pin is active high, and controls the state of the switch.
Applying a continuous high signal will hold the switch in the ON
state. The switch will move into the OFF state when the active
high is removed, or if a fault is encountered. For all versions, an
undervoltage on V IN or a junction temperature in excess of
140°C overrides the ON control to turn off the switch.
In addition, excessive currents will cause the switch to turn off in
the FPF2200 and FPF2201. The FPF2200 has an Auto-Restart
feature which will automatically turn the switch ON again after
450ms. For the FPF2201, the ON pin must be toggled to turn-on
the switch again. The FPF2202 does not turn off in response to
an over current condition but instead remains operating in a
constant current mode so long as ON is active and the thermal
shutdown or UVLO have not activated.
Fault Reporting
Upon the detection of an over-current condition, an input UVLO,
or an over-temperature condition, the FLAGB signals the fault
mode by activating LO. In the event of an over-current condition
for the FPF2200 and FPF2201, the FLAGB goes LO at the end
of the blanking time while FLAGB goes LO immediately for the
FPF2202. If the over-current condition lasts longer than
blanking time, FLAGB remains LO through the Auto-Restart
Time for the FPF2200 while for the FPF2201, FLAGB is latched
LO and ON must be toggled to release it. With the FPF2202,
FLAGB is LO during the faults and immediately returns HI at the
end of the fault condition. FLAGB is an open-drain MOSFET
which requires a pull-up resistor between VIN and FLAGB.
During shutdown, the pull-down on FLAGB is disabled to reduce
for quick output discharge when the switch is turned off. This
features become more attractive when application requires
large output capacitor to be discharged when switch turns-off.
However, V OUT pin should not be connected directly to the
battery source due to the discharge mechanism of the load
switch.
Thermal Shutdown
The thermal shutdown protects the die from internally or
externally generated excessive temperatures. During an over-
temperature condition the FLAGB is activated and the switch is
turned-off. The switch automatically turns-on again if
temperature of the die drops below the threshold temperature.
current draw from the supply. A 100K
pull up resistor is
recommended to be used in the application.
Current Limiting
The current limit ensures that the current through the switch
doesn't exceed a maximum value while not limiting at less than
a minimum value. The minimum current at which the parts will
limit is set to 500mA. The FPF2200 and FPF2201 have a
blanking time of 30ms (nominal) during which the switch will act
as a constant current source. At the end of the blanking time,
the switch will be turned-off. The FPF2202 has no current limit
blanking period so it will remain in a constant current state until
the ON pin is deactivated or the thermal shutdown turns-off the
switch.
FPF2200-FPF2202 Rev. B
9
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| 202D121-3-60/42-0 | BOOT MOLDED |
| EBC36DRTN-S13 | CONN EDGECARD 72POS .100 EXTEND |
| AD780BR | IC VREF SERIES SHUNT PREC 8-SOIC |
| VE-2TF-EY | CONVERTER MOD DC/DC 72V 50W |
| GBM25DCST | CONN EDGECARD 50POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FPF2201 | 功能描述:电源开关 IC - 配电 Integrated w/500mA Precision Crnt Limit RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FPF2202 | 功能描述:电源开关 IC - 配电 Integrated w/500mA Precision Crnt Limit RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FPF2213 | 功能描述:电源开关 IC - 配电 Adj High Precision Current Limit RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FPF2214 | 功能描述:电源开关 IC - 配电 Adj High Precision Current Limit RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FPF2215 | 功能描述:电源开关 IC - 配电 Adj High Precision Current Limit RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。