- 您现在的位置：买卖IC网 > PDF目录15800 > FR3-16M (TechTools)EMULATOR FLASH FLEXROM III 16MEG PDF资料下载
参数资料
| 型号： | FR3-16M |
| 厂商： | TechTools |
| 文件页数： | 8/38页 |
| 文件大小： | 0K |
| 描述： | EMULATOR FLASH FLEXROM III 16MEG |
| 标准包装： | 1 |
| 系列： | FlexROM™ III |
| 类型： | 存储器 |
| 适用于相关产品： | 外部 FLASH、EPROM 或 SRAM 设备 |
| 所含物品： | 需要 FR3 FlexROM III 仿真器、缆线（菊花链、LPT、迷你型夹和目标）、软件、有源缆线模块 |
| 其它名称： | FR316M |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
Plug the emulator into your target
Turn the target power off. Plug the ACM target interface cable into the target’s memory socket. Be careful
to align the PIN 1 end of the cable (designated with a stripe) with the PIN 1 end of the target’s socket
(usually designated with a notch, a dot or a ‘1’).
FlexROM III ACMs ship with DIP cables. If you are emulating PLCC type devices, you will need to
purchase a DIP to PLCC adapter. These are available from TechTools as well as all popular adapter
manufacturers.
PLUGGING THE CABLE IN BACKWARDS WILL
DAMAGE FlexROM III!
The number one cause of emulator failure is reverse voltage. The JEDEC standard pin-out for DIP
devices places power and ground on opposite corners of the device. If one plugs an EPROM or an
EPROM EMULATOR in backwards, it applies reverse voltage to the device or emulator, causing
permanent damage.
We added a new reverse-polarity protection circuit to FlexROM III which should greatly reduce the risk of
damage. However, we still strongly recommend that you heed these warnings and make every attempt to
avoid plugging the emulator in backwards.
If your target uses DIP sockets or a TechTools’ PLCC adapter, it is fairly easy to ensure the cable is
plugged in properly. Simply check (twice) that the RED stripe on the cable is aligned with the PIN 1 end of
the socket.
If you are using any type of adapter between the DIP cable and your target, it can get a little more
confusing. An incorrect adapter or one that is installed incorrectly could apply reverse voltages to the
emulator.
If you have ANY doubts, check it out! The simplest way to check out adapters, is to insert the adapter into
the target but do NOT insert the DIP cable into the adapter. The DIP socket provided by the adapter should
have GROUND on one corner pin and POWER on the opposite corner. On 28 pin sockets, ground should
be on pin 14 and power on pin 28. On 32 pin sockets, ground should be on pin 16 and power on pin 32.
Once you have established that the adapter is wired correctly and installed correctly, then insert the DIP
cable into the adapter, aligning its RED stripe with the PIN 1 end of the DIP socket.
PLUGGING THE CABLE IN BACKWARDS WILL
DAMAGE FlexROM III!
The old carpenters’ rule applies here: ‘MEASURE twice – CUT once.’
FlexROM III User’s Manual
6
Copyright ? 2001, TechTools
相关PDF资料 |
PDF描述 |
|---|---|
| TC1270AMVRCTR | IC RESET MONITOR 4.38V SOT143-4 |
| FR3-8M | EMULATOR FLASH FLEXROM III 8MEG |
| VE-B7W-EY-F4 | CONVERTER MOD DC/DC 5.5V 50W |
| TC1270AMVCTTR | IC RESET MONITOR 4.38V SOT23A-5 |
| VE-B7W-EY-F3 | CONVERTER MOD DC/DC 5.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FR3-1M | 功能描述:EMULATOR FLASH FLEXROM III 1MEG RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:FlexROM™ III 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| FR-31SERIES | 制造商:未知厂家 制造商全称:未知厂家 功能描述:surface mount circulator |
| FR31-SERIES | 制造商:未知厂家 制造商全称:未知厂家 功能描述:surface mount circulator |
| FR32 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Single Junction Surface Mount Isolator 800MHz, 900MHz, 1800MHz, 1900MHz, 2100MHz |
| FR-32 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:surface mount isolator |
发布紧急采购，3分钟左右您将得到回复。