- 您现在的位置：买卖IC网 > PDF目录20484 > FS-925 (Digi International)JTAG-BOOSTER FOR 386EX 5V PDF资料下载
参数资料
| 型号： | FS-925 |
| 厂商： | Digi International |
| 文件页数： | 25/56页 |
| 文件大小： | 0K |
| 描述： | JTAG-BOOSTER FOR 386EX 5V |
| 标准包装： | 1 |
| 系列： | Digi/FS Forth |
| 类型： | 闪存 |
| 适用于相关产品： | Intel 386EX，5V |
| 所含物品： | 编程器和关联的接口软件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
JTAG-Booster for Intel 386EX
2.1.
Program a Flash Device
Usage:
JTAG386 /P filename [optionlist]
The specified file is programmed into the flash memory. The flash status is
polled after programming of each cell (cell=8 or 16 bit, depending on current
data bus width). In case of a programming error, the contents of the flash
memory is written to a file with the extension DMP.
If you want a complete verify after programming, please use an additional
with file”. In most cases this additional verify step is not needed.
The type of the flash device is normally detected by the software. When
autodetection fails you should use the /DEVICE= option together with /8BIT or
/16BIT to set the right flash device and configuration. The known devices are
shown in chapter 1.9 “Supported flash devices”.
Options:
/DEVICE=devicename
The flash device is detected automatically by switching to autoselect mode. In
case of trouble you should select the flash device by using this parameter to
avoid autodetection. Combine this option with one of the following options which
specify the data bus width and the option /BYTE-MODE if applicable.
/8BIT /16BIT
Specifies the data bus width to the target flash device. You can speed up
autodetection, if you specify the correct data bus size. You need this option
together with the option /DEVICE= to explicit specify a specific flash
configuration.
/BYTE-MODE
If there is a flash device connected to the CPU which does have a byte mode pin
(8 bit and 16/32 bit bus mode), you can force it to be used as 8 bit mode with the
option /BYTE-MODE. In most cases this option will not be needed.
JTAG_386EXa.doc
25
相关PDF资料 |
PDF描述 |
|---|---|
| AT24C256-10PU-2.7 | IC EEPROM 256KBIT 1MHZ 8DIP |
| 1SMA5924BT3G | DIODE ZENER 9.1V 1.5W SMA |
| MBRB3030CTL | DIODE SCHOTTKY 30V 15A D2PAK |
| T95D157K016EZSS | CAP TANT 150UF 16V 10% 2917 |
| RH-2409D/HP | CONV DC/DC 1W 24VIN +/-09VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FS-926 | 功能描述:开发板和工具包 - ARM JTAG Booster PC Elan SC400 5V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| FS-929 | 功能描述:开发板和工具包 - ARM Forth JTAG Booster PC ARM SA-11x0 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| FS9309 WAF | 制造商:Texas Instruments 功能描述: |
| FS-931 | 功能描述:开发板和工具包 - ARM Forth JTAG Booster Elan SC520 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| FS-932 | 功能描述:开发板和工具包 - ARM Forth JTAG Booster PC Siemens PCUD 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。