参数资料
| 型号： | FS6370-01G-XTP |
| 厂商： | ON Semiconductor |
| 文件页数： | 27/28页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK GEN PLL EEPROM 16SOIC |
| 标准包装： | 3,000 |
| 类型： | PLL 时钟发生器 |
| PLL： | 是 |
| 输入： | 晶体 |
| 输出： | CMOS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:4 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 230MHz |
| 除法器/乘法器： | 是/无 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页
FS6370
Figure 5: FS6370 to FS6377
7.2 Non-Programming Migration Path
If the design has solidified on a particular EEPROM programming pattern, the EEPROM pattern can be hard-coded into a ROM-based
device. For high-volume requirements, a ROM-based device offers significant cost savings over the FS6370. Contact an ON
Semiconductor sales representative for more detail.
8.0 I2C-bus Control Interface
This device is a read/write slave device meeting all Philips I2C-bus specifications except a "general call." The bus has to
be controlled by a master device that generates the serial clock SCL, controls bus access and generates the START and
STOP conditions while the device works as a slave. Both master and slave can operate as a transmitter or receiver, but
the master device determines which mode is activated. A device that sends data onto the bus is defined as the
transmitter, and a device receiving data as the receiver.
I2C-bus logic levels noted herein are based on a percentage of the power supply (VDD). A logic-one corresponds to a nominal voltage of
VDD, while a logic-low corresponds to ground (VSS).
8.1 Bus Conditions
Data transfer on the bus can only be initiated when the bus is not busy. During the data transfer, the data line (SDA) must remain stable
whenever the clock line (SCL) is high. Changes in the data line while the clock line is high will be interpreted by the device as a START
or STOP condition. The following bus conditions are defined by the I2C-bus protocol.
8.1.1. Not Busy
Both the data (SDA) and clock (SCL) lines remain high to indicate the bus is not busy.
8.1.2. START Data Transfer
A high to low transition of the SDA line while the SCL input is high indicates a START condition. All commands to the device must be
preceded by a START condition.
Rev. 3 | Page 8 of 28 | www.onsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FS6377-01IG-XTP | IC CLOCK GEN PLL PROG 16SOIC |
| FS7145-02G-XTD | IC CLOCK GEN PLL PROG 16SSOP |
| FSA221UMX | IC SWITCH AUD USB DPDT 10-MLP |
| FSA8008AUMX | IC CONFIG SW/AUD JACK DET 10UMLP |
| FSA8008UMX | IC AUDIO JACK DETECTOR/SW 10UMLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FS6377 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Programmable 3-PLL Clock Generator IC |
| FS6377-01 | 制造商:AMI 制造商全称:AMI 功能描述:Programmable 3-PLL Clock Generator IC |
| FS6377-01G | 制造商:AMI 制造商全称:AMI 功能描述:Programmable 3-PLL Clock Generator IC |
| FS6377-01G-XTD | 功能描述:时钟发生器及支持产品 I2C PROG 3-PLL CLK RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| FS6377-01G-XTP | 功能描述:时钟发生器及支持产品 I2C PROG 3-PLL CLK RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
发布紧急采购，3分钟左右您将得到回复。